X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
X-Original-DKIM-Signature: v=1; a=rsa-sha256; c=simple; d=mail.ud03.udmedia.de; h=
	subject:to:references:from:message-id:date:mime-version
	:in-reply-to:content-type:content-transfer-encoding; s=beta; bh=
	Tc4KfMmo3mDlnNgYnVKI+mGjeLDELpTL8currfwgdT0=; b=QA3vJX+4MW6CX178
	E64sIqJgYchjiQ2nXWmzw8MfDe6I+mo470rhCYVQvuVl9UsX16YwDxnO1Idpm2g6
	6AX2RqQcLvgqc30pavXRGn1IWW6hYnmQtrW7tcIv3/b8BY5rL2YCsS0rKy2jbmqO
	3cBYQoTryez+slmutnpKjBfg7CE=
Subject: Re: [geda-user] pcb's crosshair only half-locating violations
To: geda-user AT delorie DOT com
References: <55F000F5 DOT 4090901 AT envinsci DOT co DOT uk> <55F04C94 DOT 4060401 AT jump-ing DOT de>
 <mspv5b$6dr$1 AT ger DOT gmane DOT org>
 <CAC4O8c_kGSiUWqcEtpjT44f2OavB2Z+=n0EQMN7ZWaQ1EZEiEw AT mail DOT gmail DOT com>
 <CAOFvGD6penfWAsnm7YN8R3nT9Qzgk9JZ4LDhGYQTQ92vv8xoGA AT mail DOT gmail DOT com>
 <55F2BFBD DOT 7010606 AT envinsci DOT co DOT uk>
From: "Markus Hitter (mah AT jump-ing DOT de) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Message-ID: <55F2C43F.7000907@jump-ing.de>
Date: Fri, 11 Sep 2015 14:08:31 +0200
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:38.0) Gecko/20100101
 Thunderbird/38.2.0
MIME-Version: 1.0
In-Reply-To: <55F2BFBD.7010606@envinsci.co.uk>
Content-Type: text/plain; charset=utf-8
Content-Transfer-Encoding: 7bit
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com
Precedence: bulk

Am 11.09.2015 um 13:49 schrieb Matt Rhys-Roberts:
> just haven't had time to learn how to compile the more recent builds yet.

  git clone git://git.geda-project.org/pcb
  cd pcb
  ./autogen.sh && ./configure --disable-nls --disable-doc && make

You'll need some dependencies, packages ending with '-dev'. Configure
should stop and tell you if there's something missing. After
installation of a dependency simply start over the last line. Repeat
until configure and the build completes.

No need to install it, pcb runs fine without installation:

  src/pcbtest.sh <layout file>


Markus

-- 
- - - - - - - - - - - - - - - - - - -
Dipl. Ing. (FH) Markus Hitter
http://www.jump-ing.de/