X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f X-Recipient: geda-user AT delorie DOT com DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=mime-version:in-reply-to:references:date:message-id:subject:from:to :content-type; bh=dPhLpKrwwVyWNh91o1kjXfgiUyz7nhsN0OFC/d0xKHc=; b=a134+XGlEiss5gdlpo5Woal6AaVNPjBDyth3T0mz8LUUkB8opF9qVH1B7CSL5iWYWB 1uHj1zPpAoEbDXmfVjwv4nbO+0SpbhTOiR/MD3cWTGoaxsc7BUmSyNVJnBq14uMTI9Hd azehmkJ68y8TTzMUqPH+HLXLkSlSDPy7hcqvXf1l8hvd/p+eXIfq3w85F8i/6A+xJ/fT cZkqLUUWk3BqXZNIgscJvQftjEmi6aZ2s7zQhxGCUwUT+f7pGX3dXH5b9RlyFkjb7uo1 Z7PsOO7qw7h+UfpySRZ1oyamaJlG9WZTBxqTbM8newfRYKIOyQpmHq9GgvcGIDK5lm1b yBRg== MIME-Version: 1.0 In-Reply-To: <4F9AB232.9030508@ecosensory.com> References: <4F915B7C DOT 9000009 AT schinagl DOT nl> <4F959E1F DOT 6010803 AT schinagl DOT nl> <4F997E2E DOT 7010306 AT schinagl DOT nl> <4F99CEFD DOT 10707 AT schinagl DOT nl> <20120426170536 DOT 73e21755 AT svelte> <4F9A6010 DOT 7010305 AT schinagl DOT nl> <20120427064154 DOT 44e9eb77 AT svelte> <4F9AB232 DOT 9030508 AT ecosensory DOT com> Date: Fri, 27 Apr 2012 21:18:48 -0400 Message-ID: Subject: Re: [geda-user] board fab From: Bob Paddock To: geda-user AT delorie DOT com Content-Type: text/plain; charset=ISO-8859-1 Reply-To: geda-user AT delorie DOT com Errors-To: nobody AT delorie DOT com X-Mailing-List: geda-user AT delorie DOT com X-Unsubscribes-To: listserv AT delorie DOT com Precedence: bulk > The boards are tab routed, so edges will have a > rough spot where a tab is broken off. If you can specify where the tabs are going (easy if your doing your own panel layout, not so easy with a board service), and you can make some space at the edge of the board where the tab is located, you can get clean tabs: Specify a series of very small drill holes, whatever the smallest drill the service has, that are as close together as allowed. The drill hit is then centered on what would be the edge of the board. This puts half of the drill hit into the board, and half of the drill hit into the tab. These are not plated holes, which is a problem with some places. If it is done correctly there is no clean up work. Caveat with any tab work: Study where the stress goes when the tab is broken. Putting things like ceramic caps or crystals next to the tab will result in fractured parts. If it is a bypass cap the damage is not always immediately obvious. -- http://blog.softwaresafety.net/ http://www.designer-iii.com/ http://www.wearablesmartsensors.com/