X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
        d=gmail.com; s=gamma;
        h=mime-version:in-reply-to:references:date:message-id:subject:from:to
         :content-type;
        bh=+qjRFZOxkDNu4G+ZE1BB2ZXSzry9kSO/BT3pAs4m8Ys=;
        b=EMpQo3VrVhZNg5emzTNgGDeHrcTxqDPo89llX9QtfYrh3FsCfPl24Ot3UbQ1TVJKpC
         FWpJDetdRxaJzHW0bu/QIQ1peys4z4y094Qw8cOB5shN3p6DrVa+TIdmyPwSEGZZqHrJ
         Oft0vqWsAKAkhZWz1dPks/iUdYfcY58J1rHK4=
MIME-Version: 1.0
In-Reply-To: <CALSZ9gp=_C+yr=uXjqSbH3w97nzfPXq--U+Huq_Hc5Dfuc5msQ@mail.gmail.com>
References: <CALSZ9gp=_C+yr=uXjqSbH3w97nzfPXq--U+Huq_Hc5Dfuc5msQ AT mail DOT gmail DOT com>
Date: Sat, 14 Jan 2012 17:16:43 -0500
Message-ID: <CALSZ9goGEYAO_gmLwyOf3pHSkpDhcAJxaCq8MOOgLimhO=WB_A@mail.gmail.com>
Subject: [geda-user] Via to Pin in PCB
From: Rob Butts <r DOT butts2 AT gmail DOT com>
To: geda-user AT delorie DOT com
Content-Type: multipart/alternative; boundary=00151761ca581b81aa04b68456f4
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com
Precedence: bulk

--00151761ca581b81aa04b68456f4
Content-Type: text/plain; charset=ISO-8859-1

I'm sending this again because it has been a week since I have emailed this
forum and I'm not sure if it is going to get filtered out (sorry if it is
double posted ~ I would think it would be better to create a registry of
approved users ~ imho).

I just made a quick 1.5" x 1.5" circuit board with a single SO8 footprint
so that I could access the pins of an IC on a test bench.  I placed vias
around the edge and now I'd like to make them pins so they have a solder
mask.  How can I do this?

Thanks

--00151761ca581b81aa04b68456f4
Content-Type: text/html; charset=ISO-8859-1
Content-Transfer-Encoding: quoted-printable

I&#39;m sending this again because it has been a week since I have emailed =
this forum and I&#39;m not sure if it is going to get filtered out (sorry i=
f it is double posted ~ I would think it would be better to create a regist=
ry of approved users ~ imho).<br>
<br>I just made a quick 1.5&quot; x 1.5&quot; circuit board with a single S=
O8 footprint so that I could access the pins of an IC on a test bench.=A0 I=
 placed vias around the edge and now I&#39;d like to make them pins so they=
 have a solder mask.=A0 How can I do this?<br>
<div class=3D"gmail_quote">
<br>Thanks <br>
</div><br>

--00151761ca581b81aa04b68456f4--