X-Authentication-Warning: delorie.com: mail set sender to geda-help-bounces using -f X-Recipient: geda-help AT delorie DOT com DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=mail.ru; s=mail2; h=References:In-Reply-To:Content-Transfer-Encoding:Content-Type:Message-ID:Reply-To:Date:Mime-Version:Subject:To:From; bh=f4NJQ1s9Pqt6zPxJhMw6hbBJmbY4llZvUT3Cr6j/X0s=; b=vFooGx7MdfopwqFJf4XoSAt+DgKGj8kevO2DaNLYfAxt6k1C++FpeIRfc1zcDDBOreDR9JSYaGnXTGdrFlRiR5PTLOqo0KOeuhJ1kKzccGQ6v6IsrOSlx/i4r9VmIrIMI7c5iCKhvk9x3+XDy5P6zGNvLBKjEUcTyunF0Qiidy8=; From: =?UTF-8?B?QWxleGV5IEJsaW5vdg==?= To: geda-help AT delorie DOT com Subject: [geda-help] =?UTF-8?B?UmVbMl06IFtnZWRhLWhlbHBdIEFueSBhbmdsZSBhcmNzPw==?= Mime-Version: 1.0 X-Mailer: Mail.Ru Mailer 1.0 X-Originating-IP: [85.141.193.130] Date: Thu, 26 Sep 2013 22:56:10 +0400 X-Priority: 3 (Normal) Message-ID: <1380221770.198547842@m.mail.ru> Content-Type: text/plain; charset=utf-8 X-Mras: Ok X-Spam: undefined In-Reply-To: References: Content-Transfer-Encoding: 8bit X-MIME-Autoconverted: from base64 to 8bit by delorie.com id r8QIuE87020193 Reply-To: geda-help AT delorie DOT com Errors-To: nobody AT delorie DOT com X-Mailing-List: geda-help AT delorie DOT com X-Unsubscribes-To: listserv AT delorie DOT com Precedence: bulk I found this "puller" (y-shortcut) to provide a (somewhat perverted) workaround to create an arc of arbitrary angle in the GUI :) You draw an arc of 90º (let radius be 35mil, in 1st quadrant), but we want 60º. Position cursor at the center of the arc *with keyboard cursor keys*. Disable grid (to not snap cursor to it) with shift-g. Issue command like Cursor('Warp',40.42,0,mil). Here 35/sin(60*pi/180)=40.415. Start drawing a line at that point. Carefully, to not move the mouse. Finish line around the arc. Type y for puller. Delete the line. Get an arc of 60º. Enable grid with g. It is important to zoom as much as possible because Cursor moves crosshair by rounding *mouse cursor* coordinates. Четверг, 26 сентября 2013, 10:40 -05:00 от Benjamin Bergman : > This isn't quite the answer you are looking for, but it might still be > useful: http://www.delorie.com/pcb/puller/ > > Basically, you can turn a 90º arc and a straight line into a nice > rounded corner leading into an arbitrary angle line. The final product > should be similar to what you want. > > On Thu, Sep 26, 2013 at 10:32 AM, doragasu . wrote: > > Hi, > > > > I have routed a PCB using the toporouter and I have to do lots of > > modifications to it. I would like to preserve the rounded tracks aspect that > > the toporouter produces, so I will be creating lots of arcs. > > > > Unfortunately, I can't find a way to create arcs with an angle different > > than 90º. Is there a not-too-difficult-and-time-consuming way of creating > > them? > > > > Regards, > > > > doragasu > > -- Alexey Blinov