Mailing-List: contact cygwin-help AT cygwin DOT com; run by ezmlm
List-Subscribe: <mailto:cygwin-subscribe AT cygwin DOT com>
List-Archive: <http://sourceware.org/ml/cygwin/>
List-Post: <mailto:cygwin AT cygwin DOT com>
List-Help: <mailto:cygwin-help AT cygwin DOT com>, <http://sourceware.org/ml/#faqs>
Sender: cygwin-owner AT cygwin DOT com
Mail-Followup-To: cygwin AT cygwin DOT com
Delivered-To: mailing list cygwin AT cygwin DOT com
From: "Etienne Mbuyi" <etienne DOT mbuyi AT chicagotrading DOT com>
To: "'Pierre A. Humblet'" <Pierre DOT Humblet AT ieee DOT org>
Cc: <cygwin AT cygwin DOT com>
Subject: RE: cygwin ver 1.5.12-1 on win2k3
Date: Wed, 20 Jul 2005 09:53:52 -0400
MIME-Version: 1.0
Content-Type: text/plain; 	charset="us-ascii"
Content-Transfer-Encoding: 7bit
In-Reply-To: <129f01c58d31$2a0b6170$3e0010ac@wirelessworld.airvananet.com>
Message-ID: <USCHI00S01F76R9iWUm000001e8@uschi00s01.chicagotrading.com>
X-IsSubscribed: yes

That was a retype = typo. I will go head and give your recommendation a try.

-----Original Message-----
From: Pierre A. Humblet [mailto:Pierre DOT Humblet AT ieee DOT org] 
Sent: Wednesday, July 20, 2005 9:45 AM
To: Etienne Mbuyi
Cc: cygwin AT cygwin DOT com
Subject: Re: cygwin ver 1.5.12-1 on win2k3

That looks fine, except that all the XXXPrivelege rights should
XXXPrivilege, AFAIK. Was that a cut and paste or a retype?
Use editrights to list the privileges of  cron_x.

Cron-diagnose was not designed for 2k3, so it's useless there.
My advice is to run cron-config. When prompted say that want
to reinstall the service.
It will prompt you for a user to run under, just say cron_x
I forgot if it will reset the privileges or keep them as they are.


Pierre


----- Original Message ----- 
From: "Etienne Mbuyi" <etienne DOT mbuyi AT chicagotrading DOT com>
To: "'Pierre A. Humblet'" <Pierre DOT Humblet AT ieee DOT org>
Cc: <cygwin AT cygwin DOT com>
Sent: Wednesday, July 20, 2005 9:31 AM
Subject: RE: cygwin ver 1.5.12-1 on win2k3


> The steps outlined below were used to install cron on a different win2k3
> server and it works. For some reason the same procedures don't work on a
> different server.
> 
> $ net user cron_x password /add /yes
> $ net localgroup administrators cron_x /add
> $ editrights -a SeAssignPrimaryTokenPrivelege -u cron_x
> $ editrights -a SeCreateTokenPrivelege -u cron_x
> $ editrights -a SeIncreaseQuotaPrivelege -u cron_x
> $ editrights -a SeServiceLogonRight -u cron_x
> $ mkpassd -l -u cron_x >> /etc/passwd
> $ cygrunsrv -I cron -p /usr/sbin/cron -a -D -u cron_x -w password
> 
> Each of these commands were completed successfully. But when trying to
start
> cron, no luck.
> 
> -----Original Message-----
> From: Pierre A. Humblet [mailto:Pierre DOT Humblet AT ieee DOT org] 
> Sent: Wednesday, July 20, 2005 9:18 AM
> To: Etienne Mbuyi"
> Cc: cygwin AT cygwin DOT com
> Subject: RE: cygwin ver 1.5.12-1 on win2k3
> 
> Etienne Mbuyi wrote:
> 
> > The output of cron_diagnose.sh does not help because it shows the same
> info
> > compared to a server where cron is working. We don't have sendmail
> install.
> > In any case here is the output of cygcheck -s -v -r. I also include the
> > crontab -l output and the error that we get when trying to start cron. 
> 
> Did you use cron-config to configure cron properly?
> Did you read what /usr/share/doc/Cygwin/cron.README says about win2k3?
> 
> Pierre
> 
> 
> 
> 




--
Unsubscribe info:      http://cygwin.com/ml/#unsubscribe-simple
Problem reports:       http://cygwin.com/problems.html
Documentation:         http://cygwin.com/docs.html
FAQ:                   http://cygwin.com/faq/