Mailing-List: contact cygwin-help AT sourceware DOT cygnus DOT com; run by ezmlm
List-Subscribe: <mailto:cygwin-subscribe AT sources DOT redhat DOT com>
List-Archive: <http://sources.redhat.com/ml/cygwin/>
List-Post: <mailto:cygwin AT sources DOT redhat DOT com>
List-Help: <mailto:cygwin-help AT sources DOT redhat DOT com>, <http://sources.redhat.com/ml/#faqs>
Sender: cygwin-owner AT sources DOT redhat DOT com
Delivered-To: mailing list cygwin AT sources DOT redhat DOT com
Message-ID: <3ABF4589.9B966206@certum.pl>
Date: Mon, 26 Mar 2001 15:35:05 +0200
From: Jacek Trzcinski <jacek AT certum DOT pl>
Reply-To: jacek AT certum DOT pl
X-Mailer: Mozilla 4.7 [en] (WinNT; U)
X-Accept-Language: en,pdf
MIME-Version: 1.0
To: Corinna Vinschen <cygwin AT cygwin DOT com>, cygwin AT cygwin DOT com
Subject: Re: stunnel
References: <3AB882C3 DOT 7BCDC988 AT certum DOT pl> <012001c0b1f2$d3c5a000$0200a8c0 AT lifelesswks> <3AB8B9C9 DOT 8B28A06C AT certum DOT pl> <005701c0b24f$d5ce4700$0200a8c0 AT lifelesswks> <3AB9A995 DOT 898783F5 AT certum DOT pl> <20010326132932 DOT E1725 AT cygbert DOT vinschen DOT de>
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit


Hi Corinna !
Thank's. It of course compiled and consolidated itself but how programs
work after cutting lines which one does not like ? :)
I had to enable switch -f (foreground mode) to stunnel work OK and its
behaviour then was similar to windows version of stunnel from
stunnel.org.
I tested it with nescape and it really works. 
I do not suppose it will work like linux daemon without any changes.
Without
-f switch program simply ends. Perhaps I will have to make typical
windows service or something what behaves like sshd under cygwin which
is seen
on process list under cygwin after executing from command line, will not
I ?

Best regards
Jacek

Corinna Vinschen wrote:
> 
> On Thu, Mar 22, 2001 at 08:28:21AM +0100, Jacek Trzcinski wrote:
> >
> > Hi !
> > Thank's for response.
> > I'm just going to send inquiry to stunnel authors but now I can say You
> > about two erors I report during unix way building of stunnel packet
> >
> > 1) module pty.c - it reports during compilation explicit use of ioctl
> > function
> > and undefined symbol I_PUSH. When I included hedaer file sys/ioctl.h to
> > this file ioctl message disappeared but error concerned with I_PUSH
> > left. This symbol is used in any invocation of ioctl function in this
> > module. I did not find it in any header file of my cygwin installation
> 
> Correct. I had the same problem when porting OpenSSH for the first time.
> The patch is pretty simple. Since I_PUSH has no sense on Cygwin, the
> corresponding source now looks like:
> 
>         #ifndef __CYGWIN__
>           ioctl (fd, I_PUSH, "foo");
>         #endif
> 
> > 2) I locked ioctl invocation in pty.c to see next errors during stunnel
> > building. Now pty.c compiled OK and during consolidation phase ld
> > reports error that it "can not find setgroups function needed by module
> > stunnel.o". As in case I_PUSH I did not find it in any header file of my
> > cygwin installation.
> >
> >
> > Have You any suggestions ?
> 
>         #ifndef __CYGWIN__
>           setgroups (...);
>         #endif
> 
> Corinna
> 
> --
> Corinna Vinschen                  Please, send mails regarding Cygwin to
> Cygwin Developer                                mailto:cygwin AT cygwin DOT com
> Red Hat, Inc.
> 
> --
> Want to unsubscribe from this list?
> Check out: http://cygwin.com/ml/#unsubscribe-simple

--
Want to unsubscribe from this list?
Check out: http://cygwin.com/ml/#unsubscribe-simple