Mailing-List: contact cygwin-help@sourceware.cygnus.com; run by ezmlm
Sender: cygwin-owner@sources.redhat.com
From: "Markus Hoenicka" <Markus.Hoenicka@uth.tmc.edu>
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Message-ID: <14737.35234.653000.603709@gargle.gargle.HOWL>
Date: Wed, 9 Aug 2000 16:41:06 +0000 (CT0)
To: Andre Bleau <andre.bleau@courriel.polymtl.ca>
CC: cygwin@sources.redhat.com
Subject: Re: _ctype_ not found in cygwin1.dll
In-Reply-To: <4.3.2.7.0.20000809102506.00b40228@courriel.polymtl.ca>
References: <4.3.2.7.0.20000809102506.00b40228@courriel.polymtl.ca>
Content-Transfer-Encoding: 8bit

Hi,

this sounds reasonable and was mentioned in the archives a while
ago. I was just confused by the fact that I can run the standalone app
without problems. It just bites me if I run it as a service. I rather
thought that I'd have to do some special tricks to run CygWin apps as a
service.

So for the next weeks (months?) I'll be mulling over libmysqlclient.a ...

Thanks
Markus

Andre Bleau writes:
 > After I upgraded to Cygwin 1.1.x I had the same problem while linking with 
 > a library I compiled under Cygwin B20.1. Some function inside the library 
 > was including <ctype.h> for the use of isupper, islower... These are macros 
 > using a
 > global variable of the cygwin library named _ctype_ whose declaration in 
 > ctype.h has changed between B20.1 and 1.1.x to now include the 
 > __declspec(dllimport) attribute. You will have to recompile the modules of 
 > your libmysqlclient.a that include <ctype.h>.
 > 
 > Hope this helps.
 > 
 > >Hi all,
 > >
 > >this is sort of a follow-up to my previous problem (accept() fails if
 > >I run my app as service, but succeeds if I run it standalone).
 > >
 > >I found out that my app does run fine as a server on a different B20.1
 > >installation. So I figured that my CygWin setup may be screwed up and
 > >started from scratch. I upgraded to the latest net release and rebuilt
 > >my app completely (except for libmysqlclient.a: This was compiled with
 > >B20.1, and I could not yet figure out how to compile it on 1.1.4).
 > >
 > >Now I face a different problem. My app again runs just fine as
 > >standalone, but when I try to start it as a service (using
 > >invkr153.zip) I get:
 > >
 > >"The procedure entry point _ctype_ could not be located in the dynamic
 > >link library cygwin1.dll"
 > >
 > >What is this trying to tell me? Any help will be greatly
 > >appreciated. cygcheck is attached below.
 > >
 > >Markus
 > 
 > 
 > André Bleau, ing., analyste
 > bleau@courriel.polymtl.ca
 > 
 > Département de génie électrique et         Electric Engineering and
 > de génie informatique                      Computer Engineering department
 > École Polytechnique de Montréal            Montreal Polytechnic School
 > 

-- 
Markus Hoenicka, PhD
UT Houston Medical School
Dept. of Integrative Biology and Pharmacology
6431 Fannin MSB4.114
Houston, TX 77030
(713) 500-6313, -7477
(713) 500-7444 (fax)
Markus.Hoenicka@uth.tmc.edu
http://ourworld.compuserve.com/homepages/hoenicka_markus/


--
Want to unsubscribe from this list?
Send a message to cygwin-unsubscribe@sourceware.cygnus.com