Mail Archives: opendos/1999/11/09/03:35:26
Well Bob
It seems that we see some of the same problems come back
since many of us use the same programs.
I sent this post back in March for Luca who was having a problem
with a stacker volume. I hope you can get some help from this.
If you can get a copy of Novell DOS 7 Unleashed, by Sams
Publishing Co. there is a lot of good stuff in there on Stacker.
Good luck, Bob Moss
----------------------------------------------------------------------
To: opendos AT delorie DOT com
Date: Wed, 31 Mar 1999 02:33:22 -0800
Subject: Re: I'm looking for stacker.bin
Message-ID: <19990331 DOT 023323 DOT -26337 DOT 0 DOT DOMANSPC AT juno DOT com>
From: ROBERT W MOSS <domanspc AT juno DOT com>
Reply-To: opendos AT delorie DOT com
hello Luca. I hope you have the original manual around because most of
the fixes for your problem will need this documentation to interpret the
stacker info and edit the files.
Sorry for the long post.
You did not say how you set up stacker, whether stacking the whole drive,
the free space on the drive, or a partition on the drive. When you create
a stacked drive, stacker normally, in effect, creates 'two' drives from
your original if you are stacking the complete drive. One is compressed
and one is un-compressed, for use for programs which don't work well with
compression. If you start with C: you will have C: (but it will be the
compressed volume, a hidden file called stacvol.dsk or stackvol.000), and
D: (the uncompressed volume). D: is also the boot drive.
Stacker.bin is a hidden file located in the root directory of the boot
drive and is loaded into memory each time you boot, and manages the
stacked drive. Stackvol.dsk and stacker.ini (also hidden) should also be
on the boot disk, root directory.
You should have a line in config.sys: devicehigh=c:\nwdos (or drdos?/or
opndos)\ stackhigh.sys. this will load stacker.bin in upper or extended
memory.
If you used create to set up your drive stacker bin won' know about the
drive and you will have to open stacker .ini using attrib and edit to
give it the info it needs. You will need the original documentation
manual to interpret this file. You have to copy it to another drive
(floppy) to edit it. Rename it and the software won't know you are trying
to edit it, which is a no-no for stacker. if you find no entries for your
drive you would problably enter D:\stacvol.dsk ,sw (this tells the
stacker bin that your stacked disk is d: and to swap d: for C: once the
drive is mounted if you have only one hard disk or partition). then copy
the file back again and set attrib rsh.
Using setup will normally not leave you in this mess.
**Run stacker to see if you can get a report on your drives. If you can't
access the stacked drive, look for the hidden files on drive C: If they
are in fact there, and you have access to the dos directory you can run
chkdsk /s but this takes a very long time. you can also run chkdsk /wp
if your stacker volume is set up as write protected.
***Next option, I would run setup off the original disks again.
You also did not mention which stacker you used. I have loaded both ndos
7 and the original stacker versions. I had some problems with the ndos7
version but everything seems ok on my original stacker 4.0 version
installation. Ndos sets up stacker as part of ndos but stacker sets up a
seperate directory and appears to be a cleaner install. You may want to
reinstall your stacker files if everything else fails.***
-------------------------
Bob 'doman' Moss - signing in from the north side of california..
* "Put 'buy choclate' at the top of your list of things to do today,*
* then you'll be sure to get one thing done right'..*
*"Remember, if you don't have chocolate you don't have food"!!!*
=================================================
On Tue, 23 Mar 1999 11:08:38 +0100 Luca Barbieri <barbieri AT to DOT atos DOT it>
writes:
>hello,
>
> after downolading and installing Caldera dos without problems
> I tryed to compress the disk, everything apparentely went fine,
> but after rebooting .... I got an error message: no stacker found.
>
> and in fact there are no the stacker.bin and stacker .ini files
> wich are required....
>
> why ?
>
> and most important where I can find them ?
>
_____________________________________________________________________
>Ing. Luca Barbieri | Phone : +39-11-22.5.22.11
>Security Product Manager |
>mailto:lbarbieri AT atos-group DOT com
>
>ATOS SpA v.Vaninetti 27 | http://www.atos.it
>I-10148 Torino ITALY | Fax : +39-11-2203182
>___________________________________________________________________
___________________________________________________________________
Get the Internet just the way you want it.
Free software, free e-mail, and free Internet access for a month!
Try Juno Web: http://dl.www.juno.com/dynoget/tagj.
- Raw text -