delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2017/04/22/18:30:30

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
Date: Sun, 23 Apr 2017 00:28:21 +0200
From: Kai-Martin Knaak <kmk AT familieknaak DOT de>
Disposition-Notification-To: Kai-Martin Knaak <kmk AT familieknaak DOT de>
To: geda-user AT delorie DOT com
Subject: Re: [geda-user] slots in plane
Message-ID: <20170423002821.74863a3c@akka>
In-Reply-To: <MWHPR04MB0479EDF219E4F030CC2D10EBA21A0@MWHPR04MB0479.namprd04.prod.outlook.com>
References: <MWHPR04MB0479EDF219E4F030CC2D10EBA21A0 AT MWHPR04MB0479 DOT namprd04 DOT prod DOT outlook DOT com>
X-Mailer: Claws Mail 3.14.1 (GTK+ 2.24.31; x86_64-pc-linux-gnu)
MIME-Version: 1.0
X-Provags-ID: V03:K0:Y3f+Gk/GVTMuVv5Mz3xQo8QC1d/wPBhB6Mz9ZhyQCoUCdwPDMh4
QBXo3KtiIbO/V9h3u4Zd5mcuo0g///fhzfE0mJn8onhnh3Ff14L6l5yWRc+YnyF8yNoGTl8
JZL9q54M1KCHHJMJ/vjVBNbBwgk6Lic/aUakG1ENtWlN0UR6Xt1ViPPVr0ryCZVMGGvap8y
oXyNuGbZKJxSlEjuNYwGg==
X-UI-Out-Filterresults: notjunk:1;V01:K0:Wg7pXaxw0gE=:zl9o+BGDrBuyFoE3L82IlO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=
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

--Sig_/lYk25bDnYeBZ4qAHP+gHgL_
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: quoted-printable

"McKay, Roy L [PHYSA] (mckay AT iastate DOT edu) schrieb am 21. April 2017:

> Some years ago I cut slots in a power plane using the line operation
> and after the lines were drawn, remove them and the plane left the
> area of the lines (+ clearances) open.  i.e. no copper of the plane
> filled back in once the lines were removed.  I now need to do that
> operation again and I cannot recall how to do it.  Would someone
> enlighten me how this is done

This is what I do: Draw an ordinary line with the minimum width the GUI
will allow. This happens to be 0.0003 mm, which is way smaller than the
fab is able to produce. Depending on the policy of the manufacturer I
then either remove the lines in the gerbers with gerbv (select the line
and hit the delete key). Alternatively, I just add a note that the
overly thin lines can be safely ignored.

Hope, this helps,

---<)kaimartin(>---
--=20
Kai-Martin Knaak
Email: kmk AT familieknaak DOT de
=C3=96ffentlicher PGP-Schl=C3=BCssel:
http://pool.sks-keyservers.net:11371/pks/lookup?search=3D0x6C0B9F53

--Sig_/lYk25bDnYeBZ4qAHP+gHgL_
Content-Type: application/pgp-signature
Content-Description: OpenPGP digital signature

-----BEGIN PGP SIGNATURE-----

iF0EARECAB0WIQSPAtn8zsMVlh17BFa31GSIbAufUwUCWPvZBQAKCRC31GSIbAuf
U/rhAJ48zyaQf1ic/+qGV1EPpPSzwoEcaQCfa0RXzIVW3nkedWj6WsEljVJk+XU=
=kmtn
-----END PGP SIGNATURE-----

--Sig_/lYk25bDnYeBZ4qAHP+gHgL_--

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019