delorie.com/archives/browse.cgi | search |
X-Authentication-Warning: | delorie.com: mail set sender to geda-user-bounces using -f |
X-Recipient: | geda-user AT delorie DOT com |
DKIM-Signature: | v=1; a=rsa-sha256; c=relaxed/relaxed; |
d=gmail.com; s=20120113; | |
h=mime-version:in-reply-to:references:date:message-id:subject:from:to | |
:content-type; | |
bh=KGn0qurd9kyYa58InnzMr1ax6dDqaUlo7Wf1LGu18Uw=; | |
b=U1DhiowLF8ZwSMUNB2S8XHE0cy+Yfbq956kgtipqCNZF0jmK9NHea+5ABDskPs6s2W | |
7h8SHuPhxl9jKiVf9+e3bGFBUxoKyjqFZe7uVZFG8giyWOr++V4gaSBCTr3XuzJuqtbg | |
FZ+vax4VFSutXkDbtzZkNG3SWEg0G58k4DNvHYqJNTuR1D/Px4Xcdb5ihQcF6YRMDnFf | |
Zc2UtifQn9DseSpZjfejMZADJvUGz8PfNdjyQlSiaz9iU2AS90ykFz1b/VFnTds/w3A8 | |
QyN0SkHnZiJaGa4qH7x9uTfUTG8Cw+4002gHosPwzdQWvFmx8X3WnSPR4AgsxiOJDi1v | |
Uv8w== | |
MIME-Version: | 1.0 |
X-Received: | by 10.68.240.36 with SMTP id vx4mr1767466pbc.140.1390918396070; |
Tue, 28 Jan 2014 06:13:16 -0800 (PST) | |
In-Reply-To: | <52E799AE.1050407@estechnical.co.uk> |
References: | <CALSZ9grNCBNGwof1bXwyFic92HJ15QxFDUiRT8HfLOVB12Q92w AT mail DOT gmail DOT com> |
<20140128005339 DOT 9636 DOT qmail AT stuge DOT se> | |
<CAM2RGhQX+g4Z=gUY7mawDdgfY7PZEzP=hBJpVnkv62mmME__ow AT mail DOT gmail DOT com> | |
<52E799AE DOT 1050407 AT estechnical DOT co DOT uk> | |
Date: | Tue, 28 Jan 2014 09:13:15 -0500 |
Message-ID: | <CAM2RGhROQdkxH7pA+kN0kqaEaNenyF53Ery9rZ64OgirWMGM2w@mail.gmail.com> |
Subject: | Re: [geda-user] 0.5mm pitch connector suggestions |
From: | Evan Foss <evanfoss AT gmail DOT com> |
To: | geda-user AT delorie DOT com |
Reply-To: | geda-user AT delorie DOT com |
Errors-To: | nobody AT delorie DOT com |
X-Mailing-List: | geda-user AT delorie DOT com |
X-Unsubscribes-To: | listserv AT delorie DOT com |
I have used a lot of SMT flat flex to board connectors and Ed Simmons is correct about melting the damn things. That said the display manufactures do not leave us much choice and if you get a connector made from the correct material the melting point is higher. I must admit I prefer to solder the ones that use less dense footprints. Something like this is my preference 62674-201121ALF but they only go up to something like 30 positions. They fan the pins out on both sides which makes hand soldering a lot easier and it is a glass composite. Take a look at this one FH40-50S-0.5SV Sorry no break out board. -Evan On Tue, Jan 28, 2014 at 6:51 AM, Ed Simmons <ed AT estechnical DOT co DOT uk> wrote: > > On 28/01/2014 03:38, Evan Foss wrote: >> >> Ada Fruit has breakout boards for that. >> http://www.adafruit.com/products/1436 >> http://www.adafruit.com/products/1325 >> http://www.adafruit.com/products/1492 >> >> On Mon, Jan 27, 2014 at 7:53 PM, Peter Stuge <peter AT stuge DOT se> wrote: >>> >>> Rob Butts wrote: >>>> >>>> 0.5mm pith flat ribbon cable and comes with a small surface mount zif >>>> connector that I think will be nearly impossible to solder to a circuit >>>> board. >>> >>> It's possible to solder by hand with a good eye and a steady hand. >>> >>> But you could also try manual reflow. Dispense enough solder paste >>> across all the pads, never mind paste on top of the soldermask, put >>> the connector in place, and use hot air to reflow the solder paste. >>> >>> Capillary forces and soldermask rules out shorts and pulls the >>> connector into position. >>> >>> Pick a connector with more material and tolerance for higher >>> temperatures to not accidentally melt it with the hot air. >>> >>> >>> //Peter >>> > > We found these connectors are quite tricky too, but creating the right > reflow profile manually using the hot air tool and a thermocouple to monitor > the temperature made it entirely possible. They don't melt if you observe > the correct profile! > -- Home http://evanfoss.googlepages.com/ Work http://forge.abcd.harvard.edu/gf/project/epl_engineering/wiki/
webmaster | delorie software privacy |
Copyright © 2019 by DJ Delorie | Updated Jul 2019 |