X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:x-received:in-reply-to:references:date:message-id
	:subject:from:to:content-type;
	bh=ZEvpXl/7ocjjHj7auqy1jYbsqNQjuHM2NVPVXANrsPw=;
	b=gMQiowDz8BQOwwr2rnZdz0Pm5X2wWrRf3jC7+W5+NS+fLi1FfloVOy3xmGCG3vQHV6
	ZbvYlNKXsZ8fQZE6kj6Mw4Ygt3y6bAyhCIJK3SBMPNC4Ol2sOc+vL9tBEKX7935/Gr++
	ooIpO0l8NovPXp+bDZuytjWcYXCjFGzdze41i+OouB3nYGBiZryhoxEfT+wnSpYgrfB4
	9j+mEi5z613TsE+JsrhRIPZXangHkjnQiGovLbSezbMjjval1YvJrN+heVQS28JjgA59
	6eLWYwamkS9knzV3npFmBC2y35zY7PBM6RfVWhiLzBk+OtuvuODnVvIvfuLEnsQxZcjB
	PguQ==
MIME-Version:	1.0
X-Received:	by 10.60.55.74 with SMTP id q10mr18682573oep.80.1368857586404;
	Fri, 17 May 2013 23:13:06 -0700 (PDT)
In-Reply-To:	<51970516.6040101@neurotica.com>
References:	<51970516 DOT 6040101 AT neurotica DOT com>
Date:	Sat, 18 May 2013 08:13:06 +0200
Message-ID:	<CAL5HA=DVx7-YL=hrUkAzDh18ncWU7ffwmuzyhGUk8dzaZuKzyA@mail.gmail.com>
Subject:	Re: [geda-user] ITEAD?
From:	Jasper <funkybob AT gmail DOT com>
To:	geda-user AT delorie DOT com
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

--089e013a16942fe33b04dcf7fe6e
Content-Type: text/plain; charset=ISO-8859-1

Hi Dave,

I have used seeedstudio's service with gEDA a few times and the boards came
out good. I don't have experience with itead but I think they're basically
the same service.

http://www.seeedstudio.com/depot/fusion-pcb-service-2-layers-p-835.html?cPath=70_71

Best regards,

Jasper


On Sat, May 18, 2013 at 6:35 AM, Dave McGuire <mcguire AT neurotica DOT com> wrote:

>
>   Hey folks.  Has anyone here used ITEAD (http://www.iteadstudio.com/) for
> PCB prototyping runs?  I was wondering how good they are, and if they
> digest
> PCB's gerbers ok.
>
>                 Thanks,
>                 -Dave
>
> --
> Dave McGuire, AK4HZ
> New Kensington, PA
>

--089e013a16942fe33b04dcf7fe6e
Content-Type: text/html; charset=ISO-8859-1
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr">Hi Dave,<div><br></div><div style>I have used seeedstudio&=
#39;s service with gEDA a few times and the boards came out good. I don&#39=
;t have experience with itead but I think they&#39;re basically the same se=
rvice.</div>
<div style><br></div><div style><a href=3D"http://www.seeedstudio.com/depot=
/fusion-pcb-service-2-layers-p-835.html?cPath=3D70_71">http://www.seeedstud=
io.com/depot/fusion-pcb-service-2-layers-p-835.html?cPath=3D70_71</a><br></=
div>
<div style><br></div><div style>Best regards,</div><div style><br></div><di=
v style>Jasper</div></div><div class=3D"gmail_extra"><br><br><div class=3D"=
gmail_quote">On Sat, May 18, 2013 at 6:35 AM, Dave McGuire <span dir=3D"ltr=
">&lt;<a href=3D"mailto:mcguire AT neurotica DOT com" target=3D"_blank">mcguire AT ne=
urotica.com</a>&gt;</span> wrote:<br>
<blockquote class=3D"gmail_quote" style=3D"margin:0 0 0 .8ex;border-left:1p=
x #ccc solid;padding-left:1ex"><br>
=A0 Hey folks. =A0Has anyone here used ITEAD (<a href=3D"http://www.iteadst=
udio.com/" target=3D"_blank">http://www.iteadstudio.com/</a>) for<br>
PCB prototyping runs? =A0I was wondering how good they are, and if they dig=
est<br>
PCB&#39;s gerbers ok.<br>
<br>
=A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 Thanks,<br>
=A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 -Dave<br>
<span class=3D"HOEnZb"><font color=3D"#888888"><br>
--<br>
Dave McGuire, AK4HZ<br>
New Kensington, PA<br>
</font></span></blockquote></div><br></div>

--089e013a16942fe33b04dcf7fe6e--

- Raw text -