X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:x-received:in-reply-to:references:date:message-id
	:subject:from:to:content-type;
	bh=S195Dxkw1O0O8LZPbI+sWHOnuzyQurFfsnRcpIz9r4c=;
	b=ApD8Ua2Kz5iAj2g79WdqexiFeHsAKqnPQR+sxXyACtJADOf8Ya6ZsksnuUA0cTkIkR
	c8jLSxQQlW5fwew06p0wn2ZXUNTva1ZQQHJVL6YLvu79bNIbTRl7Sg8/r+UAbj/xufur
	w+S9HwSG9iLk6mFXtEM3dKkQcqTba8rNxb4kw96WO12KxS9WFxgwa8diCF6fE6WFf/7e
	ZLw7RFZz2EGAcHds9HIn12BwbBJAlaArSbZIIHxCbxJzLqgE5MZqdDm85Dvk2V9/YiNd
	sW1OtZ6y2npYHMjKrPCLM5tzaMytGE7Quc3UmOgCCQmwBnbCpYkzORtDM1E5XaJAEMcW
	9+wQ==
MIME-Version:	1.0
X-Received:	by 10.50.79.233 with SMTP id m9mr873914igx.53.1367241311851; Mon,
	29 Apr 2013 06:15:11 -0700 (PDT)
In-Reply-To:	<CACPio-6UObAv=3O-UVTA0et7wJdPWg+tjMKk-J4D3OFQ3J77kQ@mail.gmail.com>
References:	<CACPio-6UObAv=3O-UVTA0et7wJdPWg+tjMKk-J4D3OFQ3J77kQ AT mail DOT gmail DOT com>
Date:	Mon, 29 Apr 2013 09:15:11 -0400
Message-ID:	<CAPYb0EG0V0FUaU26x1zSFVRY7Lqs=2tG2v4Q0+nUWCC13sTBpw@mail.gmail.com>
Subject:	Re: [geda-user] no footprint = no netlist?
From:	Bob Paddock <bob DOT paddock AT gmail DOT com>
To:	geda-user AT delorie DOT com
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On Mon, Apr 29, 2013 at 8:47 AM, Nathan Stewart
<therealnathanstewart AT gmail DOT com> wrote:

> audio circuits manage to couple snap
> crackle and pop in ways that are difficult to imagine

Check out That Crops. Design Notes on studio grade audio:
http://www.thatcorp.com/

> I'm willing to entertain either gschem/pcb solutions or changing the design,
> although I'd really like to avoid a PCB mounted socket - due to board size /
> cost issues.  Any suggestions?

The PCB footprint does not have to represent the device physically.

If you were planing on wiring to vias anyway, make a footprint with
pins (holes) instead.
Simple row of holes as a footprint for a complex round tube socket is just fine.
Put your wires there rather that vias.

- Raw text -