delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2012/05/29/19:18:14

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
X-Google-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
d=google.com; s=20120113;
h=mime-version:in-reply-to:references:date:message-id:subject:from:to
:content-type:content-transfer-encoding:x-gm-message-state;
bh=jUCj2Z8Yexepoq+qbSBctlg7/mI6YVU2mDhEfu2dtUw=;
b=Im3z/dS/3oDF5uVVrKS8oxg1cmQea8IjB8QD4hNz+4Jz9ImaZGsoPtNpJN3BRhlHHa
UU//Fo3bxP/U5doL2EOIwEHXRL4tCEGaptbZpZZ6o/27ksBfGo5wFaQ7XSVxMlZGNbhZ
JUBN+87mdhrTH97PhqOytkRUp65e8xOgsCVZvgvphy/SVaEalHx0EHAWaYaKl30zyUZ6
7fJkvhfmLILcZfRF3P1m2+XEBo3st/i6003WQQj1jvSGt9W5T+r7vZIMIZjZ5DohYsLx
AZaQxpJoqrqNnXTpd51+/CSSWfTP4fVh3EK1YUZ9k04uLIeDAh34EPiupM0+uqU5Y6fv
uirQ==
MIME-Version: 1.0
In-Reply-To: <20120529223834.GA28710@nome03.eecs.oregonstate.edu>
References: <20120529223834 DOT GA28710 AT nome03 DOT eecs DOT oregonstate DOT edu>
Date: Tue, 29 May 2012 16:09:27 -0700
Message-ID: <CAN0Jx-97Sr=9tdOZzvMs2kH_=y4sz5oPzyNQWC4_Gd-ZRCX1eA@mail.gmail.com>
Subject: Re: [geda-user] rectangular pad with hole? howto?
From: Russell Dill <Russ DOT Dill AT asu DOT edu>
To: geda-user AT delorie DOT com
X-Gm-Message-State: ALoCoQla86FmbY6bor7S2t5S1hXnpE/yuf4dIbDDbdh8WR3WUYk4vzWXW1VJFsZXArfEDfv8v7WT
X-MIME-Autoconverted: from quoted-printable to 8bit by delorie.com id q4TNG3aW027302
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

Just put a pad and pin in the same place. Give them both the same name
and don't forget to put a 'onsolder' pad for the opposite side too.

On Tue, May 29, 2012 at 3:38 PM, Traylor Roger
<traylor AT eecs DOT oregonstate DOT edu> wrote:
> Gang,
>  I'm trying to use an edge launch SMA connector with snap in terminals
>  as seen at http://www.bomarinterconnect.com/sma_edgemnt.htm.
>
>  I'd like to make the signal return pads rectangular and place the
>  plated through retention hole in them.
>
>  Not finding a way to create a rectangular pad with a plated through
>  hole. Any ideas?
>
>  Thanks,
>  Roger Traylor

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019