X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
X_CMAE_Category:	, ,
X-CNFS-Analysis:	v=2.3 cv=Ubcvt5aN c=1 sm=1 tr=0 a=OAvc3ylXTZnwW13UMKQG5A==:117 a=OAvc3ylXTZnwW13UMKQG5A==:17 a=jpOVt7BSZ2e4Z31A5e1TngXxSK0=:19 a=KGjhK52YXX0A:10 a=IkcTkHD0fZMA:10 a=jlQd9YhnVdoA:10 a=Jdjhy38mL1oA:10 a=JbhlE8a8jZIA:10 a=pGLkceISAAAA:8 a=Mj1Xp5F7AAAA:8 a=BGn9bn1rAAAA:8 a=wY3Kp6I2T3cUsUCxkk0A:9 a=QEXdDO2ut3YA:10 a=OCttjWrK5_uSHO_3Hkg-:22 a=bjWQBSCV0hpNPQM4DZhn:22 a=pHzHmUro8NiASowvMSCR:22 a=n87TN5wuljxrRezIQYnT:22
X-CM-Score:	0
X-Scanned-by:	Cloudmark Authority Engine
X-Authed-Username:	dG9tZGVhbkB3YXZlY2FibGUuY29t
X_CMAE_Category:	, ,
X-CNFS-Analysis:
X-CM-Score:
X-Scanned-by:	Cloudmark Authority Engine
Authentication-Results:	smtp02.emerald.cmh.synacor.com smtp.mail=tomdean AT wavecable DOT com; spf=permerror; sender-id=permerror
Authentication-Results:	smtp02.emerald.cmh.synacor.com header.from=tomdean AT wavecable DOT com; sender-id=permerror
Authentication-Results:	smtp02.emerald.cmh.synacor.com smtp.user=tomdean; auth=pass (LOGIN)
Subject:	Re: [geda-user] Home soldering LGA-12 suggestions
To:	geda-user AT delorie DOT com
References:	<CAM7eQ1n51EYFBiRTcTMDKvx19REkJiFb_Jr00LkbAkfGq6BqfA AT mail DOT gmail DOT com>
	<20200102201054 DOT f43d1cba4af49e5830a8d4dd AT gmail DOT com>
	<CAM7eQ1ktA=G34oWMe2-ED_u=iUOwey1Ovp7B3sosoH0fF3J+nw AT mail DOT gmail DOT com>
From:	"Thomas D. Dean (tomdean AT wavecable DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Message-ID:	<9ce8b270-fe3a-b568-663a-8cb6efea9bd3@wavecable.com>
Date:	Thu, 2 Jan 2020 13:41:36 -0800
User-Agent:	Mozilla/5.0 (X11; Linux x86_64; rv:60.0) Gecko/20100101
	Thunderbird/60.9.0
MIME-Version:	1.0
In-Reply-To:	<CAM7eQ1ktA=G34oWMe2-ED_u=iUOwey1Ovp7B3sosoH0fF3J+nw@mail.gmail.com>
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On 1/2/20 12:02 PM, Rob Butts (r DOT butts DOT geda AT gmail DOT com) [via 
geda-user AT delorie DOT com] wrote:

Look thru http://www.seattlerobotics.org.

Basically, use a fine screwdriver tip.  Apply lots of flux.  Drag a blob 
of solder across the pins.  Clean the tip by wiping.  Apply more flux. 
Drag the tip across the pins.

Inspect and use braid to clean up shorts, missed blobs, etc.

Tom Dean

- Raw text -