X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
X-Mailer:	exmh version 2.8.0 04/21/2012 with nmh-1.6
X-Exmh-Isig-CompType:	repl
X-Exmh-Isig-Folder:	inbox
From:	karl AT aspodata DOT se
To:	geda-user AT delorie DOT com
Subject:	Re: [geda-user] running mult. versions of kicad
In-reply-to:	<20190401173627.5c03239f@demon>
References:	<20190329142529 DOT 0883A81FA169 AT turkos DOT aspodata DOT se> <20190401173627 DOT 5c03239f AT demon>
Comments:	In-reply-to "(graahnul DOT grom AT gmail DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
	message dated "Mon, 01 Apr 2019 17:36:27 +0300."
Mime-Version:	1.0
Message-Id:	<20190402140358.53A6381FA166@turkos.aspodata.se>
Date:	Tue, 2 Apr 2019 16:03:58 +0200 (CEST)
X-Virus-Scanned:	ClamAV using ClamSMTP
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

Dmitry:
> On Fri, 29 Mar 2019 15:25:28 +0100 (CET)
> karl AT aspodata DOT se wrote:
> > I'm doing some pcb-rnd/pcb <-> pcbnew file conversion
> > test.
> > Is there anyone here who knows how to run kicad v4.0.7
> > and v5.1.0 side by side so I can test and compare ?
> > Currently I build and istalled kicad, footprints,
> > libraries and the 3dthings in:
> >  /usr/local/kicad_4.0.7/
> >  /usr/local/kicad_5.1.0/
> > and I can start them as /usr/local/kicad_xxx/bin/pcbnew,
> > but they are using the same config files in
> > ~/.config/kicad/.
> I would try to create two separate folders to be used as
> home directories for each kicad instance, then launch it
> with $HOME environment variable set to point to
> appropriate directory. Hopefully, kicad will
> use /.config/kicad/ subdirectories from these "homes". E.g.:
> 
> $ mkdir /tmp/kicad4home /tmp/kicad5home
> $ HOME=/tmp/kicad4home /usr/local/kicad_407/bin/pcbnew
> $ HOME=/tmp/kicad5home /usr/local/kicad_510/bin/pcbnew

To sum up, that seems to work with some pain.

///

I tested with
 mkdir -p ~/kicad/{4.0.7,5.1.0}
and
 HOME=/home/karl/kicad/4.0.7 /usr/local/kicad_4.0.7/bin/pcbnew
and it worked fine except that it cannot find 3dlibraries.

5.1.0 was a pain to configure the fp paths and such.

Running
 HOME=/home/karl/kicad/4.0.7 /usr/local/kicad_4.0.7/bin/kicad
doesn't work, since it couldn't (?) find its associated binaries
for some reason.
Adding a
 export PATH=/usr/local/kicad_4.0.7/bin:$PATH
didn't help.

So, how do the kicad devs do this, or do they just forget about any 
older version than bleading edge ?

Regards,
/Karl Hammar

- Raw text -