delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2018/07/11/00:33:51

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
X-Original-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
d=gmail.com; s=20161025;
h=date:from:to:subject:message-id:in-reply-to:references:mime-version
:content-transfer-encoding;
bh=bYM+Oks5VU2jjD4/dGQjwrCRoT+I4fJ54RM+RVN4pOU=;
b=Ofxn0Wg8O6sLTsdLbcltXl2BHIRIZUwsDSKw6fLGZP4gqlksStIcQ1sntdBXgmyML1
P5FMgWO6N5i5DFUmA9s30scdvp1KUSS8CFVa/nnwqWlbuoriyefLpJRA90T1ycx6gZ2+
hWchjszAm1FatyOPHqNFGYYf+Z6lqFcNiFhymlsfsP7MDdWyKoOUJFNVMdxCGzOkaN8R
uUcjMnzRdb5OYazMGSp+HaVAdqiEyFhIAarc90UMcxzTSpTaPntGwRZTHuzePj6/j2cB
3HwENHR/jSS6TaUkgF1U2P72vkoIBVa0EXNqNU0FMnFCUaqftY/rxOLXMZevHnoVtDVr
24MQ==
X-Google-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
d=1e100.net; s=20161025;
h=x-gm-message-state:date:from:to:subject:message-id:in-reply-to
:references:mime-version:content-transfer-encoding;
bh=bYM+Oks5VU2jjD4/dGQjwrCRoT+I4fJ54RM+RVN4pOU=;
b=rZP0tdupJEKxWjc+9ziOfa2TZLaF9DXWsA3xWwAcyP2XEiti3BeTzIkzcQWpZS/zwG
+Q9nSMIDvGAfH8SKm8poP7grxv2CM1H52A5BgiUVivL5saJOmdeBF3Z6CLVdSrgQw5PR
SYncz/1yn6/E5AQhSJwPeOXJYfVjZ9j3jrwEd7+fMBmu1KaCP5dqKHaplg7DJY/wbhcY
bvM5+ZzHDNziziAA3I8IDTZFNiJXFWf79sYo7expGUiV+wWdMY22iSFDYAzS5tUEVQO1
/t5YPmlokr1WTpBB8HgiuoxvMWxCmWtyLXVR0VcM6vgWqARkIRTxLBZZNdd8JfWzCiLc
rc7g==
X-Gm-Message-State: APt69E3Hsb/ae+h1JI9sFK+B53SYWGvhwBzFvEEaL5TErCcHB5fs8pWe
9uQTmCgDwZhp4UHnGO/NwctS1w==
X-Google-Smtp-Source: AAOMgpfQyGoViAHHCu3hoXLROAGYdo3G5c1H5xqg5Lk75Yt70aIVikuuMQe59yAyO2AGk40Ui2LJTQ==
X-Received: by 2002:a19:7d84:: with SMTP id y126-v6mr4930245lfc.94.1531283543784;
Tue, 10 Jul 2018 21:32:23 -0700 (PDT)
Date: Wed, 11 Jul 2018 06:32:19 +0200
From: "Nicklas Karlsson (nicklas DOT karlsson17 AT gmail DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
To: geda-user AT delorie DOT com
Subject: Re: [geda-user] How to define for an exposed pad to connect to 3
pins/pads
Message-Id: <20180711063219.810829ac137e677cee560a8e@gmail.com>
In-Reply-To: <CALSZ9gqdtu23r8Zgeis+En9LQoH340G8SMYJJTkSj2zcKpTHoA@mail.gmail.com>
References: <CALSZ9gqdtu23r8Zgeis+En9LQoH340G8SMYJJTkSj2zcKpTHoA AT mail DOT gmail DOT com>
X-Mailer: Sylpheed 3.7.0 (GTK+ 2.24.32; x86_64-pc-linux-gnu)
Mime-Version: 1.0
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

On Tue, 10 Jul 2018 17:36:31 -0400
"Rob Butts (r DOT butts2 AT gmail DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com> wrote:

> I'm using a 36 pin stepper motor driver.  There are 3 ground pins (AGND,
> DGND and PGND) and one huge exposed pad under the center of the IC.
> Internally the exposed pad is connected to all of these ground pins/planes.
> 
> How would the PAD definition look if I want all of these pads to connect to
> the exposed pad?  And how does this exposed pad get defined in the
> schematic symbol?

I have a circuit board with a L6474 stepper motor driver. I added a lot on pins there exposed pad is to get good thermal conductivity but have failed to get an opening in solder mask. I could also have chosen to add an ordinary pad but in such case I have to do without the pins because they are not allowed to overlap.

For several footprint pins to connect to same net I used same pin number. Observe that I failed to get a hole in solder mask with the pin approach!!

Then trying right now it is possible to toggle visibility but not to draw on solder mask, this is also the case in old version of pcb-rnd but newest version I do not know. Perfect solution would be to add solder mask polygon to the footprint I have. I have not investigated possibility to manually edit file and add solder mask.


I participated in discussion maybe one or two years ago and possibility to use any of the ordinay drawing primitives on any layer also in footprints is sometimes very useful.


Regards Nicklas Karlsson

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019