X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
Subject:	Re: [geda-user] (Off-topic) Question wrt driving HV piezo transducer
To:	geda-user AT delorie DOT com
References:	<c3aa1897-3806-3f72-feef-85551a63c2db AT linetec DOT nl>
	<alpine DOT DEB DOT 2 DOT 00 DOT 1802091235090 DOT 12270 AT igor2priv>
	<6221de93-bb98-d397-79b4-eecf3975c2e6 AT linetec DOT nl>
	<alpine DOT DEB DOT 2 DOT 00 DOT 1802091324350 DOT 12270 AT igor2priv>
	<f2259553-7015-8fc8-33b2-8ca8be6c5a45 AT linetec DOT nl>
	<alpine DOT DEB DOT 2 DOT 00 DOT 1802091427450 DOT 12270 AT igor2priv>
	<20180209161532 DOT 6AF57804CEFA AT turkos DOT aspodata DOT se>
	<alpine DOT DEB DOT 2 DOT 00 DOT 1802091735590 DOT 12270 AT igor2priv>
	<20180209204934 DOT CAA35804CEFA AT turkos DOT aspodata DOT se>
	<alpine DOT DEB DOT 2 DOT 00 DOT 1802100406500 DOT 12270 AT igor2priv>
	<b125c1d5-48a1-c1dc-3ee1-db9875d50bf6 AT linetec DOT nl>
	<c49d734f1b1f6373733e6f9935afff35 AT iae DOT nl>
	<da435a2d-0bd0-f6d7-7d9a-05394665621c AT linetec DOT nl>
	<aeedf5b6a230f39abdc82845a57a8b1b AT iae DOT nl>
	<1a5665d2-c032-29f3-6de3-d4e3cd52f42b AT linetec DOT nl>
	<8a6378847926baf01ef4fca1383d2bb9 AT iae DOT nl>
	<d97f467d-6623-bee0-d63e-1d9daba345d0 AT linetec DOT nl>
	<cfd1ba65-665b-98cf-86e6-92500a4f560e AT ecosensory DOT com>
	<23accb16-b75d-b195-772d-2fe3c80a420e AT linetec DOT nl>
From:	"John Griessen (john AT ecosensory DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Message-ID:	<4346c80d-d241-d768-ae8d-5ee39242719a@ecosensory.com>
Date:	Fri, 16 Feb 2018 15:46:53 -0600
User-Agent:	Mozilla/5.0 (X11; Linux x86_64; rv:52.0) Gecko/20100101
	Thunderbird/52.6.0
MIME-Version:	1.0
In-Reply-To:	<23accb16-b75d-b195-772d-2fe3c80a420e@linetec.nl>
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On 02/16/2018 11:22 AM, Richard Rasker (rasker AT linetec DOT nl) [via geda-user AT delorie DOT com] wrote:
> this exact same half H-design is used in 100 kHz PWM motor drives and performs just fine).

My question is not about the speed of switching, but of the overall response time.

My center tapped push pull can handle 6 microsecond plus and 6 us minus pulses.  80kHz rep rate.

It's all easier, (not saturating), if you can do with slower, thus my question.

100kHz is the fastest most ordinary switcher cores run at, so there is easy shopping from 40kHz to 100kHz,
and you would not want to be below 40kHz so it is less audible.

- Raw text -