X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
X-Original-DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=wellesley.edu; s=gmail;
	h=from:content-transfer-encoding:subject:message-id:date:to
	:mime-version;
	bh=Y+CsQEynflHZkpJeCZ39WNHpgsIm2LoQnxkRpv0iJCs=;
	b=YM0DFdIMk6eUw31+7XGIFnqY8d9FSPc6/DAmmpqFb8dEclYeuaLUCO6tDWjIQV1tj+
	lEx6rMXkj3JodRMNM40Jc0iOIwxDurJTA36u01aj7WTgeF3Bfcra60C67knFAyBJnU0b
	1ed43NM2j3weGo0WPYlnHF+etB1BEPj3a0y+j1onaTdhI07bWqTmbrIKZXpb1jXKRYEX
	w51zTEiNpTGdYfLb2VVunwwgWbFOK5igGS7n/Gnl9UyP2NHQLGYDcScNnWQ/lKKCI/Cv
	ydLy0PY1ewYnHxxQjWEXwTzwSSCVHUAFWxRdYEyZ7dkA8Fsg9AdF372XwcX8PMmTxr65
	ExYg==
X-Google-DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=1e100.net; s=20130820;
	h=x-gm-message-state:from:content-transfer-encoding:subject
	:message-id:date:to:mime-version;
	bh=Y+CsQEynflHZkpJeCZ39WNHpgsIm2LoQnxkRpv0iJCs=;
	b=mGD65R+wi798xAKkhdrvmjG4MrrTwWzhYMU8xXCcHrOzhMnW8rH8x2fK9+LnGUDpY7
	Slhy/X+m9Sx+TXTFX3j3MqL1m4Lzpo9aYtrQGhS/Cgov/4+FKRFjEf/h8aZPceC0dI0D
	nCcvSECNPQZ2Z/uUClun6ye+hR/O7P48wb0sH1vuNEOlOeTC4BhqD3hcLD4gqUW5Jluf
	4AEfDI+BNSDWDwQg9R0kEbepvsCGI+NCtyoVl8Xeow6JqSh1U3U916Wh+2chEjJ0oPi5
	LQ1iYKJDrKkIq/bIEHgtlVt0cfUFkWBc/M4WfcmcOVoNYYbS2xblsOWyvtq4gyM6d+y9
	IW+Q==
X-Gm-Message-State:	AEkoouvy/tXbbKuk6OrRR11a8DrsjA6CSJN6CasYPcjX6ziUdQM70uRScDnqpsK06ChyO5wI
X-Received:	by 10.200.49.129 with SMTP id h1mr32927895qte.103.1471991418119;
	Tue, 23 Aug 2016 15:30:18 -0700 (PDT)
From:	"James Battat (jbattat AT wellesley DOT edu) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Subject:	[geda-user] pcb: moving portions of a layout around
Message-Id:	<199EEF6F-3BCF-4AA5-AB60-9EA59EDE899F@wellesley.edu>
Date:	Tue, 23 Aug 2016 18:30:15 -0400
To:	geda-user AT delorie DOT com
Mime-Version:	1.0 (Mac OS X Mail 7.3 \(1878.6\))
X-Mailer:	Apple Mail (2.1878.6)
X-MIME-Autoconverted:	from quoted-printable to 8bit by delorie.com id u7NMUMa4005060
Reply-To:	geda-user AT delorie DOT com

What are some recommended ways to move around portions of a pcb layout?

For example, say I want to move a set of 60 components (with inter-connecting traces) and shift them up and over by a few inches?
I know that I can drag select, but often only parts of components are selected that way (some pads, but not the whole element), and then I spend a fair amount of time individually selecting traces/elements that were not captured by the drag select. This is especially true in a dense region of board where a drag select of components that I want would also select the components that I want to leave alone.  I always end up with a lot of Shift-clicking to select what I want (and only what I want).

I usually end up turning off silk & pins/pads, then drag selecting the traces + vias, then turning back on the silk & pins/pads to grab the elements.  But I’m sure that there’s a better way.

Thanks,
James

- Raw text -