X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=date:from:to:subject:message-id:mail-followup-to:references
	:mime-version:content-type:content-disposition:in-reply-to
	:user-agent;
	bh=J5cUCfyUmJeBHzwSyaUlso/Oh3xKtFWGajK/LgxnUe0=;
	b=WLWq/oeQ/wf4GMtXZrJrMNrbH2HX4lNGBU26n7nyBshQySxOhrRRPLG8Ec124MPDCe
	7jEVTY5WvCsa3GUPIQB2QYXqtZTLAmzSE8ILcO6Pywpycr6ZI6D0xMoelt+LGUt1Y4mE
	t3PCjiXitqMuWXn7Y8Z+HArC3+2pyyfR39gWTfuDmxkbo+/lP1s7hdhlos0fgeyqZbn5
	Bq+cC6GzYJJVk1R4wQg9lt+tNIiXAyCSU+mTddoemohHYTyCEQ5ck7BRuRbbD4AiQWu1
	l9ROSCTqMzNlFULqi3O4mQN0fvqIbrgKsWwEZ9SZCPuU3O9rgXVvqHybdtiG6VyhOEYF
	Iw7w==
X-Received:	by 10.112.151.146 with SMTP id uq18mr6737444lbb.38.1392414796856;
	Fri, 14 Feb 2014 13:53:16 -0800 (PST)
Date:	Sat, 15 Feb 2014 01:53:12 +0400
From:	Vladimir Zhbanov <vzhbanov AT gmail DOT com>
To:	geda-user AT delorie DOT com
Subject:	Re: [geda-user] gschem nets not connecting to pins and other nets
Message-ID:	<20140214215312.GB28744@localhost.localdomain>
Mail-Followup-To:	geda-user AT delorie DOT com
References:	<CALSZ9grbQLCHrdnB00HEMiKMkGYCL3PBYNiQosLhiJapQPZ4aA AT mail DOT gmail DOT com>
	<20140214194823 DOT GA28744 AT localhost DOT localdomain>
	<CALSZ9grFny1qYt-YaiZ8aP47dcq+QjTCnad62bpQ3=y3HRcn+A AT mail DOT gmail DOT com>
	<CALSZ9gptgOuZOCciEZOKqMD-=+cQko=wLtUFpBtSiXwDBfAHyQ AT mail DOT gmail DOT com>
	<CALSZ9goJ1gr=VifjWT2ibLdmW0b7bYL2T1e7KONcYDK+xmJAoA AT mail DOT gmail DOT com>
MIME-Version:	1.0
In-Reply-To:	<CALSZ9goJ1gr=VifjWT2ibLdmW0b7bYL2T1e7KONcYDK+xmJAoA@mail.gmail.com>
User-Agent:	Mutt/1.5.21 (2010-09-15)
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On Fri, Feb 14, 2014 at 04:17:27PM -0500, Rob Butts wrote:
>    I have rebooted with no change.  I'm attaching a screenshot of the
>    schematic.  I'm getting yellow dots on pins, both yellow dots and red
>    squares on pins.  Is there a way to reset all of the default settings?
>    I'm at a stall point!
Look, the status line is below.  It is showing Grid(100,100) now.
If you hit 'os' once it should show Grid(100R,100). This says the
resnap mode is active. The current mode is shown on the right-hand side
of the status line. If moving nets or the opamp itself doesn't help,
select this component, hit '<Shift>-h s' (go down the symbol) and resnap
all the pins of the symbol. Then hit 'os' two times to go to normal snap
mode (snap on). Translate symbol into zero coordinates (hit
'et') before saving. Then go back ('<Shift-h u') and try to connect your
nets.

- Raw text -