X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=date:from:to:subject:message-id:mail-followup-to:references
	:mime-version:content-type:content-disposition:in-reply-to
	:user-agent;
	bh=UJY8LCXv9DrTr+9yAMwnJAv2TkJwLGMvmRo7iGQSCXk=;
	b=HzpVBTND4lrxPDQ9GDfGEiyIRvOy3ZelkFjLf2Pu3C3sy5tCvZnSQIpq0MAvhLSZF0
	YyWBU6GxmJMU/3fykMcCK3l5zBsJKL5m7cBYAH+Ukk2v+NibMhvv/PSWeB47Ld4wiUqy
	8u5+8sEKGQ7dVqaDwzpeZ1lApFGKTMsdeRLFMuc1AzNXl2zAmuhubVyW0y8fYWKdLZXA
	e8e4/VnoTyQ73mq2lIRKCfqnpO7auKk5wPRKziS0ZYAf2GNmtPwzPs8neHgduAKPX85b
	/9zKb5YH/BwrYSRIWtIsrIG47RjwgsqLG6+jmb5VE8tEtMW45iY8IYKyzC8cN3W+sOJK
	5MWQ==
X-Received:	by 10.112.164.5 with SMTP id ym5mr3065442lbb.48.1392407307315;
	Fri, 14 Feb 2014 11:48:27 -0800 (PST)
Date:	Fri, 14 Feb 2014 23:48:23 +0400
From:	Vladimir Zhbanov <vzhbanov AT gmail DOT com>
To:	geda-user AT delorie DOT com
Subject:	Re: [geda-user] gschem nets not connecting to pins and other nets
Message-ID:	<20140214194823.GA28744@localhost.localdomain>
Mail-Followup-To:	geda-user AT delorie DOT com
References:	<CALSZ9grbQLCHrdnB00HEMiKMkGYCL3PBYNiQosLhiJapQPZ4aA AT mail DOT gmail DOT com>
MIME-Version:	1.0
In-Reply-To:	<CALSZ9grbQLCHrdnB00HEMiKMkGYCL3PBYNiQosLhiJapQPZ4aA@mail.gmail.com>
User-Agent:	Mutt/1.5.21 (2010-09-15)
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On Fri, Feb 14, 2014 at 01:47:41PM -0500, Rob Butts wrote:
>    I'm making changes to a schematic.  I deleted a quad op-amp and added a
>    dual op-amp.  I am trying to put the nets in but I'm getting fluky
>    results.  It will put a yellow dot where there is a pin.  It won't
>    connect (remove the red square) when I connect to a pin.
>    I tried closing the schematic and reopening but that doesn't fix it.
>    Anybody see this?
>    Thanks

This could happen if your symbol or its pins are not on the grid due to
moving or creating them when the grid was off. You can resnap the symbol
in question in the resnap mode. Hit 'os' several times to cycle through
the snapping modes and look at the status line for hints. If this
doesn't help, go down the symbol and resnap its pins.

- Raw text -