X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
X-Google-DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=google.com; s=20120113;
	h=mime-version:x-received:in-reply-to:references:date:message-id
	:subject:from:to:content-type:x-gm-message-state;
	bh=3cqdpAB4Kmwv2GBxPpGeQD4WZkHEnjK28ckqIvcbE9A=;
	b=iHd/akEQJzshU78a0FdLvIBh0UxsHWR5hI+72tCdU6/QguM8QsvbTgZsEWMrNXkcwg
	QURyZ7GwrhWkmpWtuWYSjNXknV98q4VMZ9aVAFPZiwido9mQImibicWeeliAUccwhrK9
	/7/zFlmD3nkcQRhqc2tBrkKqKBfMInJwxxm3xJ7+M1qKu81d4f5vP96q5VwAy1JQFZUt
	kKsfFOnZQFI+B3bfXEPaiYlgNpLQbBa5t1rz8jNmVpyWfkxTO8AheMP2qOTi72LRBgRx
	Yl9gU9Hbq/yNTG2zqXCAPB8sgs74pGNom9VMKoqGyKB0U/+Y4+rNAAu8bjigQlqTJ47Q
	i2tg==
MIME-Version:	1.0
X-Received:	by 10.180.185.44 with SMTP id ez12mr20431799wic.33.1362510338317;
	Tue, 05 Mar 2013 11:05:38 -0800 (PST)
In-Reply-To:	<CAN0Jx--zBQjM8R5dikyMj6wqjKb+qwXvuGt7gxJwS5v7cm-vBQ@mail.gmail.com>
References:	<51350C42 DOT 2070801 AT estechnical DOT co DOT uk>
	<CAN0Jx--zBQjM8R5dikyMj6wqjKb+qwXvuGt7gxJwS5v7cm-vBQ AT mail DOT gmail DOT com>
Date:	Tue, 5 Mar 2013 11:05:38 -0800
Message-ID:	<CAN0Jx-9OZ5x3Pf_M+_M+7XhHAeKBbG8xcbtp+BYVkB=MeZA3Ag@mail.gmail.com>
Subject:	Re: [geda-user] Stencil tooling holes
From:	Russell Dill <Russ DOT Dill AT asu DOT edu>
To:	geda-user AT delorie DOT com
X-Gm-Message-State:	ALoCoQnN+PCXlXBsxF6jIiPBUylav9losO9MSnnWoUNcYHx2zv21qWj8pTXDHyXcWgYE74A42N3U
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

Oh, one more thing, if you have lone openings in you paste stencil,
they can be mistaken for paste on a fiducial, which some board houses
will remove through an automatic or manual process (not sure which).
Be sure to specify when ordering a stencil to please not mess with my
stencil.

On Tue, Mar 5, 2013 at 9:05 AM, Russell Dill <Russ DOT Dill AT asu DOT edu> wrote:
> On Mon, Mar 4, 2013 at 1:04 PM, Ed Simmons <ed AT estechnical DOT co DOT uk> wrote:
>> Hi all,
>>
>> Please could someone offer some advice for placing tooling holes into my
>> design (these are off the edges of the board itself and will only be used
>> for stencil layers)
>>
>> How would you go about this? Is this something I should make a custom
>> footprint for?
>>
>> Thanks in advance - best regards,
>> Ed
>
> I have a couple of patches that makes it really easy to draw on any
> layer. In the case of tooling holes for a stencil, I place an unplated
> drill, in the tooling hole location, and then add a zero length trace
> of the appropriate size in the same location. I also use this to make
> arbitrary soldermask windows and adding text to the fab drawing
> "Exposed copper OK", "1.40mm 20 degree bevel", etc. I could be used
> for bridging 0 ohm resistor footprints as well.
>
> Layer(10 "toppaste")
> (
>         Attribute("PCB::skip-drc" "1")
>         Attribute("PCB::skip-print" "1")
>         Attribute("PCB::merge" "toppaste")
> [snip]
> )

- Raw text -