X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
X-Virus-Scanned:	amavisd-new at neurotica.com
Message-ID:	<512F8ECF.8070908@neurotica.com>
Date:	Thu, 28 Feb 2013 12:07:27 -0500
From:	Dave McGuire <mcguire AT neurotica DOT com>
User-Agent:	Mozilla/5.0 (X11; Linux x86_64; rv:17.0) Gecko/20130106 Thunderbird/17.0.2
MIME-Version:	1.0
To:	geda-user AT delorie DOT com
Subject:	Re: [geda-user] surface mount confusion
References:	<alpine DOT DEB DOT 2 DOT 00 DOT 1302280929500 DOT 4237 AT tehzcl2 DOT tehzcl-arg> <512F803B DOT 2040301 AT neurotica DOT com> <alpine DOT DEB DOT 2 DOT 00 DOT 1302281024240 DOT 4237 AT tehzcl2 DOT tehzcl-arg> <512F885D DOT 3000304 AT neurotica DOT com> <alpine DOT DEB DOT 2 DOT 00 DOT 1302281059270 DOT 4237 AT tehzcl2 DOT tehzcl-arg>
In-Reply-To:	<alpine.DEB.2.00.1302281059270.4237@tehzcl2.tehzcl-arg>
X-Enigmail-Version:	1.4.6
Reply-To:	geda-user AT delorie DOT com

On 02/28/2013 12:00 PM, kqt4at5v AT gmail DOT com wrote:
>>>>> Being a beginner with not so steady a hand I choose to stick to
>>>>> through hole devices But I just tried a simple board with a soic
>>>>> chip I made a breakout board for TPIC2810D 1 chip and a single
>>>>> row header of 16 pins The board is single sided so the chip is on
>>>>> the solder side and the header is on the opposite side I setup
>>>>> the board so pin 1 of the chip is connected to pin 1 of the
>>>>> header and so on When viewed in pcb the traces appear not be
>>>>> connected correctly but when I export to gcode they are correct
>>>>> Would someone set an old fella straight
>>>>
>>>> I would love to help but I'm not sure I understand specifically
>>>> what the problem is...can you describe what you mean by "traces
>>>> appear not to be connected correctly"?
>>>>
>>>>> If I were to try this on a more complex board it would make me
>>>>> crossed eyed
>>>>
>>>> Nah...I lay out surface mount PCBs and build prototypes for them
>>>> all the time.  It's just a different skill set from doing
>>>> through-hole work. I actually despise through-hole work anymore,
>>>> and minimize it when possible.  (not just due to the additional
>>>> assembly cost when a design goes to volume production!)
>>>>
>>>
>>> I attached screwed up pcb
>>
>>  Ok.  At first glance, it appears that the traces are on the bottom
>> (solder) side of the board...they will of course make contact with the
>> through-hole header pins, but the footprint for the TPIC2810D is on the
>> top (component) side of the board...there will be no electrical
>> connection to them.
>>
>>  You'll need to either redraw those traces on the top side of the
>> board, move the chip to the bottom of the board, or use vias to get
>> those signals up to the top of the board.  Get it?
> 
> Got it
> This was good little practice

  Yes.  Good luck with your board!

             -Dave

-- 
Dave McGuire, AK4HZ
New Kensington, PA

- Raw text -