X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:in-reply-to:references:date:message-id:subject:from:to
	:content-type;
	bh=c1i5eAknAPy3XrYf7m2a/A7K2QCybZfpQT6roI1+ouM=;
	b=GXo3CuZAgTfsvTqasBwid3GxSjreO7v8W25kdDZZA2Hpm/NzDmczr+Tbd9I/0VuP/v
	NgZVSU1EX2XuDsytkqOl6o7n39Gb2aYspr0EV8WjC6kHN88VE766QM6VEfnTXYzvkzab
	QPg8DiXO++VLhlnR9Ll216sCJ9oXZ3RMLRZ5qC/D6/eHnR9PWKS5HQ0+6N7NsiloyCSd
	zMwD2FNmHB22PBF4P2eRipwHH+jSMa0UQZi3/eVbHW0sAqC+UsiTB4Z3rJijsmtfnwnp
	nJ/DaC+u+/4fzwHy5Si/aKiQ7oDIGkgHQdtU9Jsy2jhzWS45wMPIJ/KHoLUZqI6Dbuh3
	cwrQ==
MIME-Version:	1.0
In-Reply-To:	<5010F048.3010304@plastitar.com>
References:	<CA+GuLwe5sPPWJQAQtX2mYTFYz5Dnt_wPy42ywZnY37dagsrEHQ AT mail DOT gmail DOT com>
	<5010D52B DOT 8030800 AT plastitar DOT com>
	<5010F048 DOT 3010304 AT plastitar DOT com>
Date:	Wed, 25 Jul 2012 14:29:55 -0700
Message-ID:	<CA+GuLwefxmvdSsYC5BwuhVhFjiffiG3LgwBU2q=+=5Zk7YwWkA@mail.gmail.com>
Subject:	Re: [geda-user] how to use "clearance" and mask in pcb footprint
From:	Ram Bhamidipaty <rambham AT gmail DOT com>
To:	geda-user AT delorie DOT com
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

Hi,

Thank you. I have seen the document - and in fact that was how I
managed to create
the footprint.

My real problem is that I am complete newbie in term of knowing how to
design a pcb.
What I do not know is how I am supposed to think about the clearance
and mask options?

The mask option seems simple - it just defines that area where the
solder mask will
have holes. What I don't know is how much of a hole is needed? Should
I just have the
solder mask line up with the edge of the pad/pin or should I have some
extra room? How
much extra room?

And clearance - I really have no idea what that means...

-Ram



On Thu, Jul 26, 2012 at 12:22 AM, Phil Taylor <phil AT plastitar DOT com> wrote:
> OOPS:
>
> On 7/26/2012 1:27 AM, Phil Taylor wrote:
>>
>> Ram,
>>
>> This document explains the clearance and mask numbers ... which are not
>> as obvious as you might at first think.
>
>
> http://www.brorson.com/gEDA/land_patterns_20070818.pdf

- Raw text -