X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
Date:	Tue, 10 Jul 2012 10:42:20 -0700
From:	Andrew Poelstra <asp11 AT sfu DOT ca>
To:	geda-user AT delorie DOT com
Subject:	Re: [geda-user] [PATCH] Allow to create metric Gerber and drill
	files, hopefully final version.
Message-ID:	<20120710174220.GA9111@malakian.lan>
References:	<CAKakQcdTgG6E2h+UgWoh-ujP6vFDH=voY-PBJR3OFG2awqL0_A AT mail DOT gmail DOT com>
	<20120705101614 DOT GA19974 AT visitor2 DOT iram DOT es>
	<20120706202633 DOT GA28355 AT malakian DOT lan>
	<20120706213340 DOT GA30622 AT visitor2 DOT iram DOT es>
	<20120707104156 DOT 17641 DOT qmail AT stuge DOT se>
	<20120708042719 DOT GE1637 AT malakian DOT lan>
	<20120709224559 DOT GB4355 AT visitor2 DOT iram DOT es>
	<20120709234535 DOT GD23449 AT malakian DOT lan>
	<20120710004318 DOT GA28800 AT visitor2 DOT iram DOT es>
	<20120710014622 DOT GE23449 AT malakian DOT lan>
MIME-Version:	1.0
In-Reply-To:	<20120710014622.GE23449@malakian.lan>
User-Agent:	Mutt/1.5.20 (2009-12-10)
X-MIME-Autoconverted:	from 8bit to quoted-printable by pobox.sfu.ca id q6AHmY2S000591
X-MIME-Autoconverted:	from quoted-printable to 8bit by delorie.com id q6AHmerf010807
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

On Mon, Jul 09, 2012 at 06:46:22PM -0700, Andrew Poelstra wrote:
> On Tue, Jul 10, 2012 at 02:43:18AM +0200, Gabriel Paubert wrote:
> > 
> > Ok, it seems the bug is not actually a bug since octogonal pads
> > are procuded as polygons in Gerber output. I suspect that the
> > OCTOGONAL case in aperture definitions is dead code.
> >
> 
> This is my suspicion too. I'll investigate.
>

Yeah, it's dead. I have patch waiting in the wings to delete
it (and delete the #if 0'd stuff nearby). It's all been disabled
since forever, is probably bitrotten, and keeping old code around
is git's job now.
  
> > > 
> > > > 
> > > > The fact that imperial Gerber have 2 orders or magnitude better
> > > > resolution than the associated drill is a problem (25.4µm versus
> > > > 0.254µm). At least metric gives micrometer resolution for both. 
> > > >
> > > 
> > > Is this a problem with the spec, or our implementation?
> > 
> > Our implementation, for losing the last digit. This causes visible
> > centering problem in the smallest vias, and is a regression from
> > earlier revisions.
> >
> 
> Sigh.. the problem is that keeping the last digit causes overflows.
> We'll have to figure out a smarter solution.
>

This is a toughie. I may end up adding a pcb_printf specifier.

-- 
Andrew Poelstra
Email: asp11 at sfu.ca OR apoelstra at wpsoftware.net
Web:   http://www.wpsoftware.net/andrew
"You shouldn't trust every quote you read on the Internet." -- Socrates

- Raw text -