X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:in-reply-to:references:date:message-id:subject:from:to
	:content-type;
	bh=zAbrJizsCHAJ0R9AG/yv5mqbGRhfSXun8OZBQdpe73g=;
	b=wxEYkT+etDJDs/ieoIAGvJ26NvUbHi4Mrm6LSdlCZ0AoFidO83LX2a54lyMqSXkGF3
	mNjLfcMo2VXdmQFum0UsVtX30oKh0p0iucw8uuDeRjCZIDDbF92sVNEHc4aanSIBh/r2
	o/Kfl6XwBJpbLNZANjXG8Et+UT+wdx0pdUj7GlZF87VR6839Ehmp4PJyISBrGEog5pXE
	huhelYgKzLATIH3H2nX0Q5voOmHMWzaCDg+uetUAZDwT2IzV1xQpndEuwSfi5kgY+eDd
	6gPW3/M7Sr12ev9Zb54HhjMWsXU4CKEzAG4a6BlZjip9bGEdaomFlcfKeNRB0sYhLJQP
	cvmw==
MIME-Version:	1.0
In-Reply-To:	<CAKakQccjw9WOjhbNr=qCT8z0PvxWJSEGsfR3SmD0L4Dic=TfCg@mail.gmail.com>
References:	<CALSZ9grznvM0i=H_5hL3PXZy-UfCtC_aw_RGT112tpmfu2UgAQ AT mail DOT gmail DOT com>
	<CAKakQccjw9WOjhbNr=qCT8z0PvxWJSEGsfR3SmD0L4Dic=TfCg AT mail DOT gmail DOT com>
Date:	Fri, 30 Mar 2012 06:57:50 -0400
Message-ID:	<CAPYb0EEdVqcSW3s=D8-EbTZA+_vQbm9p3bgxv=KVM0srDk7YCw@mail.gmail.com>
Subject:	Re: [geda-user] Reed Switch vs Hall Sensor
From:	Bob Paddock <bob DOT paddock AT gmail DOT com>
To:	geda-user AT delorie DOT com
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

> Considering the low current you're putting through the reed switch I
> expect it will last a long time.

Check the data sheet for any switch that you use, even the giant 10+
Amp ones.  Some will have a *minimum* current rating, most don't have
it in the data sheet.
There has to be enough current to keep the contacts clean.  This
mostly shows up at manufacture time after cleaning the board or after
the switch had not been activated in years.
They build up an oxidation film.  To low of a current will not clear the oxide.

We use reeds by the thousands, as long as they are not physically
abused, they are glass after all, we've had no issues.

You can use an external magnet to bias a normally open reed to act
normally closed.

Allegro Micro sells booth active high and active low in the 3211 and 3212.
The data sheet makes the hysteresis curve look like the switch output
waveform, they are inverted from each other.

http://www.allegromicro.com/Products/Magnetic-Digital-Position-Sensor-ICs/Micropower-Switches-Latches.aspx

Some will work with either magnet polarity and some are unipolar.


-- 
http://blog.softwaresafety.net/
http://www.designer-iii.com/
http://www.wearablesmartsensors.com/

- Raw text -