X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=gamma;
	h=mime-version:in-reply-to:references:from:date:message-id:subject:to
	:content-type:content-transfer-encoding;
	bh=Wiuxo27sjH8iwVSdo2aL33pqMRMmr8Z1eYNTnaDe2nk=;
	b=kiHQN8HQouSZ+CdZH/2sZU0C6AguUglK/mTXBLGptPvmjyJKAoKyqH503LqtZLCM1V
	MdWHBN5TQEKHfIDDeAcoBAD2jbX/BVG5jg+2Ff0vknp/4fGdbD9by05MElruR6dMEMDp
	ERV+s+YI4tVbX0s+zIcJxwS4C+rbNYO41Hz70=
MIME-Version:	1.0
In-Reply-To:	<20111027091908.6ceb09e9@svelte>
References:	<CANGbSP=Cddkq=_7ufTzR7aE_muMWjoqA5Sn8ih-66w_Ot8Ti2w AT mail DOT gmail DOT com>
	<CANGbSPmNT6pFcE-d+Cvc=t6t3Dfo4wPp2YQ0x54zUfLgas_CcQ AT mail DOT gmail DOT com>
	<20111026105142 DOT 0f36c506 AT svelte> <CANGbSPmMZiOzBdQs5mecuWtbJh85Y02VUThnf2nxPJA==uXBDw AT mail DOT gmail DOT com>
	<201110271425 DOT p9REP4Nk024962 AT envy DOT delorie DOT com> <20111027091908 DOT 6ceb09e9 AT svelte>
From:	Alberto Maccioni <alberto DOT maccioni AT gmail DOT com>
Date:	Fri, 28 Oct 2011 14:21:13 +0200
Message-ID:	<CANGbSPm+N-OkLe6sQhJmi91-fYSALcLCUCXcQ_NbB_VBXmT9CA@mail.gmail.com>
Subject:	Re: [geda-user] pcb-20110918 compile error
To:	geda-user AT delorie DOT com
X-MIME-Autoconverted:	from quoted-printable to 8bit by delorie.com id p9SCT0W6030007
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

The only change would be to disable HAVE_SPAWNVP when cygwin is
detected; I have no clue how to do it automatically.
And also use configure --disable-gl because there is no gl port for cygwin.
By the way, in the cofigure help the option is not listed, there is
only the old --enable-gl.


2011/10/27 Colin D Bennett <colin AT gibibit DOT com>:
> On Thu, 27 Oct 2011 10:25:04 -0400
> DJ Delorie <dj AT delorie DOT com> wrote:
>
>>
>> > Is there a faq for cygwin users? I guess this tip would help
>> > many people.
>>
>> No, but consider: the windows port of PCB is targetting MinGW, not
>> Cygwin, so any differences there might cause problems.  If you
>> want to help support a Cygwin port, please do :-)
>
> It's encouraging that he's been able to build easily on Cygwin up to
> this point, so hopefully that can continue.  It would be nice to
> support both Cygwin and MinGW if it requires minimal effort.
>
> Regards,
> Colin
>

- Raw text -