| delorie.com/archives/browse.cgi | search |
| X-Authentication-Warning: | delorie.com: mail set sender to geda-help-bounces using -f |
| X-Recipient: | geda-help AT delorie DOT com |
| X-Original-DKIM-Signature: | v=1; a=rsa-sha256; c=relaxed/relaxed; |
| d=gmail.com; s=20161025; | |
| h=mime-version:reply-to:in-reply-to:references:from:date:message-id | |
| :subject:to; | |
| bh=TkZcg2WVxMe8MNFsw/3rqg6aZ02MRsB0hyIVs6oYbO4=; | |
| b=l3KvExJvsda9SrWl8c+ZkjlhQEbzKYFOXxKW0JLgG8U88pxQhXdfilfg3kAcLnYTPQ | |
| UNN4Lk+Ugk0txY05JLAgFBZZDzqraGI0OdUTh4RJRgYL6ugc0KFJlUSYIo6246mteBE6 | |
| 2tAcvFANQPAxSM47GQ8hVH4UEHHXPgI6o4LS/hgEWtZ+l4UizHNdYJJhcoSkBepM0dWC | |
| ltLnCemGQTwJ8sGIb2b3ZqnMIVNIu7CwdRKIfT1txROa76SDJXdN+sh7SNbTqlYGzBLV | |
| kuNy/13f9UUjH4CYRxCNGSdHvGolTAlokWq0ZQLDMgSvirvAbEg7DpkqEJhE3l4JWsOs | |
| bC/Q== | |
| X-Google-DKIM-Signature: | v=1; a=rsa-sha256; c=relaxed/relaxed; |
| d=1e100.net; s=20161025; | |
| h=x-gm-message-state:mime-version:reply-to:in-reply-to:references | |
| :from:date:message-id:subject:to; | |
| bh=TkZcg2WVxMe8MNFsw/3rqg6aZ02MRsB0hyIVs6oYbO4=; | |
| b=Bgz+3G1qldPU8NGFuaTbCwavKrsOpvFpqokd+LSKMV8XIYAxQ7+qVHDMm5cRdvTSiy | |
| OEjRNlEIVhLTKGaCuv0t/wsiyJpqSwHiely/dYadZxvDhJ2AhmwkD/acb75uppDeLXlM | |
| qWFmP6jHlkezaFhKuUqVSzDeQTwy24xEC0U37zm8jBqEXVrTQCPmxcFBUUxC0zOkhtU6 | |
| fggjZsexiL5m51oYz95ELFKP7zDBfhBh2gqAAr42iTRh0mmgNyJ/idoCRT7jqBOfHCAM | |
| rZFemt5RdC3zDeP5FDHlaggkUCwJGoGTQe9NfZOreY1yD+kk9hop3N4r6WtBWf+o82mn | |
| TlgQ== | |
| X-Gm-Message-State: | AIVw110yvWkGV5hjIxs5f3oQymQKiMIY5a/6Ls3Ak7HntFnzhl81TNCe |
| Y+KAiSheCQbyr+GXqKStBMWjp7dGUxjT | |
| X-Received: | by 10.84.254.10 with SMTP id b10mr8535736plm.442.1501975825846; |
| Sat, 05 Aug 2017 16:30:25 -0700 (PDT) | |
| MIME-Version: | 1.0 |
| In-Reply-To: | <xnpoca3ku4.fsf@envy.delorie.com> |
| References: | <CAKGxq80MTXzfQqoghS8JtcVo2kGh7AVDeJsEkhr6D-Wxiycvcg AT mail DOT gmail DOT com> |
| <xnpoca3ku4 DOT fsf AT envy DOT delorie DOT com> | |
| From: | "Chris Fisichella (christopher DOT j DOT fisichella AT gmail DOT com) [via geda-help AT delorie DOT com]" <geda-help AT delorie DOT com> |
| Date: | Sat, 5 Aug 2017 19:30:25 -0400 |
| Message-ID: | <CAKGxq80Hz4fjuBbeU8LjDzoJW8g97qKMSbhhTTiA187b2ZR07w@mail.gmail.com> |
| Subject: | Re: [geda-help] help with 71 pin element |
| To: | geda-help AT delorie DOT com |
| Reply-To: | geda-help AT delorie DOT com |
| Errors-To: | nobody AT delorie DOT com |
| X-Mailing-List: | geda-help AT delorie DOT com |
| X-Unsubscribes-To: | listserv AT delorie DOT com |
--f403045fff568f9788055609ff73 Content-Type: text/plain; charset="UTF-8" Hi DJ, Thank you very much for the prompt reply.I was reading the gschem documentation <http://wiki.geda-project.org/geda:gschem_symbol_creation>, and it says the pinseq needs to be a number. The pinnumber can be alphanumeric. That's what I did in my symbol fp file. I did find a mistake in the regulator symbol file <https://drive.google.com/open?id=0BwuQXPvkmCadTXNoS1JuNEVsb2s>. There should be no "L71" thanks for catching that. It's just an alphanumeric grid with letters for rows and numbers for columns. I fixed the pinnumber mistakes and can see pinname is "unknown-2" It seems to be looking for a pinsequence. I ran gschlas -e <foo.sh> and got this file <https://drive.google.com/open?id=0BwuQXPvkmCadWl9ZUDd4Yjg5aFU>. I don't see why my schematic symbol is not working with this footprint. In 170804_RegulatorSchematic, I can see the pins have pinnumber assigned as "K7" and pinsequence assigned a positive integer. I ran through gsch2pcb and still, nothing gets attached to that regulator. I am noticing some of the library symbols do not use alphanumeric pinnumbers. Perhaps I should also do that? Best, Chris On Fri, Aug 4, 2017 at 8:43 PM, DJ Delorie <dj AT delorie DOT com> wrote: > > Your schematic doesn't have the symbols embedded (gschlas -e foo.sch) so > we can't see what the schematic has for pin numbers. > > Note that the symbol must have the *numbers* (1..71) not the name > (A1..L71), unless you change the .fp file to have A1..L71 in the numbers > field. > > Importing the schematic into the pcb will replace the "name" field with > the pinnames from the schematic, so they end up with names like "ENABLE" > or "BUS4" or "PWRGOOD" depending on your design. > > --f403045fff568f9788055609ff73 Content-Type: text/html; charset="UTF-8" Content-Transfer-Encoding: quoted-printable <div dir=3D"ltr">Hi DJ,<div><br></div><div>Thank you very much for the prom= pt reply.I was reading the gschem <a href=3D"http://wiki.geda-project.org/g= eda:gschem_symbol_creation" target=3D"_blank">documentation</a>, and it say= s the pinseq needs to be a number. The pinnumber can be alphanumeric. That&= #39;s what I did in my symbol =C2=A0fp file. I did find a mistake in the <a= href=3D"https://drive.google.com/open?id=3D0BwuQXPvkmCadTXNoS1JuNEVsb2s">r= egulator symbol file</a>. There should be no "L71" thanks for catching that. It's just= an=20 alphanumeric grid with letters for rows and numbers for columns. I fixed the pinnumber mistakes and can see pinname is "unknown-2" It see= ms to=20 be looking for a pinsequence.</div><div><br></div><div>I ran gschlas -e <= ;foo.sh> and got <a href=3D"https://drive.google.com/open?id=3D0BwuQXPvk= mCadWl9ZUDd4Yjg5aFU">this file</a>. I don't see why my schematic symbol= is not working with this footprint.<br><br></div><div>In 170804_RegulatorS= chematic, I can see the pins have pinnumber assigned as "K7" and = pinsequence assigned a positive integer.<br><br></div><div></div><div>I ran= through gsch2pcb and still, nothing gets attached to that regulator.<br></= div><div><br></div><div>I am noticing some of the library symbols do not us= e alphanumeric pinnumbers. Perhaps I should also do that?<br></div><div><br= ></div><div>Best,</div><div>Chris</div></div><div class=3D"gmail_extra"><br= ><div class=3D"gmail_quote">On Fri, Aug 4, 2017 at 8:43 PM, DJ Delorie <spa= n dir=3D"ltr"><<a href=3D"mailto:dj AT delorie DOT com" target=3D"_blank">dj AT de= lorie.com</a>></span> wrote:<br><blockquote class=3D"gmail_quote" style= =3D"margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><br> Your schematic doesn't have the symbols embedded (gschlas -e foo.sch) s= o<br> we can't see what the schematic has for pin numbers.<br> <br> Note that the symbol must have the *numbers* (1..71) not the name<br> (A1..L71), unless you change the .fp file to have A1..L71 in the numbers<br= > field.<br> <br> Importing the schematic into the pcb will replace the "name" fiel= d with<br> the pinnames from the schematic, so they end up with names like "ENABL= E"<br> or "BUS4" or "PWRGOOD" depending on your design.<br> <br> </blockquote></div><br></div> --f403045fff568f9788055609ff73--
| webmaster | delorie software privacy |
| Copyright © 2019 by DJ Delorie | Updated Jul 2019 |