X-Authentication-Warning:	delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient:	geda-help AT delorie DOT com
Date:	Sat, 18 Feb 2017 09:25:50 +0100
From:	"Smilie (smilie AT posteo DOT de) [via geda-help AT delorie DOT com]" <geda-help AT delorie DOT com>
To:	geda-help AT delorie DOT com
Subject:	Re: [geda-help] Strange view in pcb!
Message-ID:	<20170218092550.57f2bac6@debian.olsr>
In-Reply-To:	<CAJXU7q__k1K8SPUv9xernFsQHM6pNke7BDktu-RUz7HaRAmMYQ@mail.gmail.com>
References:	<20170215114403 DOT 42fc309c AT debian>
	<CAJXU7q_J=dFaGVrD9atjdf3+3TFiLWiq3cyfKOzwfDWWvpT_0Q AT mail DOT gmail DOT com>
	<20170215161700 DOT 6ffbd79e AT debian>
	<CAJXU7q__k1K8SPUv9xernFsQHM6pNke7BDktu-RUz7HaRAmMYQ AT mail DOT gmail DOT com>
Organization:	Individuum auf blauem Planet
X-Mailer:	Claws Mail 3.14.1 (GTK+ 2.24.31; x86_64-pc-linux-gnu)
MIME-Version:	1.0
Reply-To:	geda-help AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-help AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

I think, PCB need some additional features:


1. split PIN/PAD Layer in two Buttons PIN and PAD.
2. make it possible, that the "auto enforce DRC clearance" works also
while moving lines.

3. the algorithm for "auto enforce DRC clearance" could be modified,
that the line will be lay around the barrier?




Am Wed, 15 Feb 2017 15:28:44 +0000
schrieb "Peter Clifton (petercjclifton AT googlemail DOT com) [via
geda-help AT delorie DOT com]" <geda-help AT delorie DOT com>:

> I think I'll have to try that to understand properly; but if you mean
> - you accidentally shorted against pins which you had switched off
> visibility for... Not sure how to avoid that fully.
> 
> Perhaps need to separate the view controls a little more. In my later
> 3D stuff (available on repo.or.cz), in 3D view turning off any layer
> also hides things like copper pads on that layer.
> 
> Peter
> 
> Peter
> 
> On 15 Feb 2017 15:19, "Smilie (smilie AT posteo DOT de) [via
> geda-help AT delorie DOT com]" <geda-help AT delorie DOT com> wrote:
> 
> > Am Wed, 15 Feb 2017 10:48:02 +0000
> > schrieb "Peter Clifton (petercjclifton AT googlemail DOT com) [via
> > geda-help AT delorie DOT com]" <geda-help AT delorie DOT com>:
> >  
> > >  Any chance you can post a screenshot of what you describe?
> > >
> > > (Imagebin.ca or similar if the files are big?)
> > >
> > > On 15 Feb 2017 10:45, "Smilie (smilie AT posteo DOT de) [via
> > > geda-help AT delorie DOT com]" <geda-help AT delorie DOT com> wrote:
> > >  
> > > > Hello guys,
> > > >
> > > > if i have an Jumper connected through all layers.
> > > > But if i disable the view of all layers, apart from a inner
> > > > signal-layer, the contacts of the connected through is not
> > > > visible. This is in my opinion a bug.
> > > > Or what is this feature for?
> > > >
> > > > lg
> > > >  
> >
> >
> > OK, i see the Failure, but i will explain the situation.
> >
> >
> > Step by step:
> >
> > 1. create a new pcb.
> >
> > 2. Load a Jumper1 and place it to the board.
> >
> > 3. Take also some SMD-footprints an place it free over the board.
> >
> > Now you wont draw a line in a (signal) middle layer, but the
> > SMD-Footprints are worry. Because this you make some layers
> > invisible.
> >
> > 4. Now you make the pins/pads invisible. Or what?
> >
> > But, you can not free draw the middle layer, because you have
> > collisions with footprints like Jumper1.
> >
> >
> >  

- Raw text -