X-Authentication-Warning:	delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient:	geda-help AT delorie DOT com
X-Google-DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=1e100.net; s=20130820;
	h=x-gm-message-state:mime-version:in-reply-to:references:from:date
	:message-id:subject:to:content-type:content-transfer-encoding;
	bh=bHa/BWil7TA1tsB1oajyPHx0dOaXTxpnaYc6oQ1Udog=;
	b=FqAnEKNSwzG+81YXIy5oXttG2pg4pjK5ysXkBoeDhWqpkyzhbfKT7O9/HZ6hf4b/3x
	BYg43GOHgfpbX4obb0b82KMfbbamOlBc7+b5xcdvGOnvKdKM+WRm7OzHaKDFDnwhZSl1
	B4wuKJNY/cy16T6hnU71IqWbSBojhJWRGqCFW4xflJdMvYB/2PKHdXyZ1YrBcoEv4S7D
	wwyJM8dk6JvodhsoC94nHa4vmB9b6HsDdWijPmwmBzjlQbnkMnu2IMOEK5F6revZcg+j
	JmTCpB6nV1/QZJXzXCOqaXbVkLTuuXljpv85KDiv3Zp40Cvr4mx5ktGwZY7y9KG0UV+r
	Ml5A==
X-Gm-Message-State:	ALoCoQmP3S1runYRDf79UpqxFTEgWMeSuv8j0zVrau+N6E/63Pjn0xA9X75iGNQYU0rleLQuOgZd
X-Received:	by 10.58.161.116 with SMTP id xr20mr1256079veb.2.1380210070164;
	Thu, 26 Sep 2013 08:41:10 -0700 (PDT)
MIME-Version:	1.0
X-Originating-IP:	[50.72.201.196]
In-Reply-To:	<CANcjc3kgTnh05LjqCd+n2VR=eYCLS3dGa4YFgsrqd_K-Xy0VYw@mail.gmail.com>
References:	<CANcjc3kgTnh05LjqCd+n2VR=eYCLS3dGa4YFgsrqd_K-Xy0VYw AT mail DOT gmail DOT com>
From:	Benjamin Bergman <ben AT benbergman DOT ca>
Date:	Thu, 26 Sep 2013 10:40:39 -0500
Message-ID:	<CA+DWcQZqqDX3Sg_F491R5zg9_dpni5HaOzEXa6O4yJWJuvn94g@mail.gmail.com>
Subject:	Re: [geda-help] Any angle arcs?
To:	geda-help AT delorie DOT com
X-MIME-Autoconverted:	from quoted-printable to 8bit by delorie.com id r8QFfBIj006533
Reply-To:	geda-help AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-help AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

This isn't quite the answer you are looking for, but it might still be
useful: http://www.delorie.com/pcb/puller/

Basically, you can turn a 90º arc and a straight line into a nice
rounded corner leading into an arbitrary angle line. The final product
should be similar to what you want.

On Thu, Sep 26, 2013 at 10:32 AM, doragasu . <esakaforever AT gmail DOT com> wrote:
> Hi,
>
> I have routed a PCB using the toporouter and I have to do lots of
> modifications to it. I would like to preserve the rounded tracks aspect that
> the toporouter produces, so I will be creating lots of arcs.
>
> Unfortunately, I can't find a way to create arcs with an angle different
> than 90º. Is there a not-too-difficult-and-time-consuming way of creating
> them?
>
> Regards,
>
> doragasu
>

- Raw text -