X-Authentication-Warning:	delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient:	geda-help AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=20120113;
	h=mime-version:in-reply-to:references:date:message-id:subject:from:to
	:content-type;
	bh=qVtASJpxx+Y2C5NxLw9enUpCZUD2P5ZakpgMVj90cE0=;
	b=gzh9TMj4aDegk+Ap4kVXv3mwbpWuuHPYFbIQEOHUOVd1tNDIShLS4fCzcL+bL6pmoe
	yRrJE61ZLmDxbRXgb1DIPkh6L44amfN8uqaVqRU8TZvDguBwszoxbQOsC0LJ42dRF8eh
	/qB0r0qU2iJP/KF0+N62BwUhxdbc2t4dpFJGW4zGRa0dOyk7gRXes9T0j22Yd7Bq13Eo
	DA6OYp5WbWMvJNhwF1m2gHFmZP1OM0VnVHbtj9kh+Lo/t7Po6rt1wjVQhivAlmzeMoZE
	KE9CcW9MMESMDSw6+0J5QgiNg41PqgH5mY92kNXHj1jnDndS+yzM7p4WdwO/7KLZCjW5
	Aksg==
MIME-Version:	1.0
X-Received:	by 10.58.118.130 with SMTP id km2mr30264730veb.0.1379394884381;
	Mon, 16 Sep 2013 22:14:44 -0700 (PDT)
In-Reply-To:	<1379351570.346568165@m.mail.ru>
References:	<1379351570 DOT 346568165 AT m DOT mail DOT ru>
Date:	Tue, 17 Sep 2013 09:14:44 +0400
Message-ID:	<CAMvDHVC2nVe2rBhN0JPGpgXRpaR1DPmYguPJk3rCt3p3nswuyQ@mail.gmail.com>
Subject:	Re: [geda-help] Two adjacent regions, separated along a given curve,
	as close as possible
From:	Vladimir Zhbanov <vzhbanov AT gmail DOT com>
To:	geda-help AT delorie DOT com
Reply-To:	geda-help AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-help AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

AFAIK, polygons themselves don't support curved borders. So if you
want something similar you can make them up adding many vertices
to a polygon. Then, if your whole fill is not very complicated
(say, a rectangle which you want to cut up) you can make one part
of the fill (left or right, top or bottom), then copy it to
another layer and after that reflect it moving two vertices to
another side. Further you need to select a very little grid size
which satisfies your meets and move the two polygons as close as
you want. Check carefully all vertices since they can overlap
somewhere.
You also can do this by editing the source file of your pcb
layout. Make the first polygon and find it in the source file,
then copy it and change coordinates of two points. Then you can
adjust your second polygon in pcb.

- Raw text -