X-Authentication-Warning:	delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient:	geda-help AT delorie DOT com
X-AuditID:	52823f54-b7fcb6d000000b8c-0e-4f2ab8ff2247
Date:	Thu, 2 Feb 2012 18:25:33 +0200
From:	=?ISO-8859-15?Q?Jaakko_Kantoj=E4rvi?= <jaakko AT darkeagle DOT dy DOT fi>
To:	geda-help AT delorie DOT com
Subject:	[geda-help] PCB: How can i make pin with copper ring only on solder layer.
	(fwd)
Message-ID:	<alpine.DEB.2.02.1202021825210.21502@darkeagle.dy.fi>
User-Agent:	Alpine 2.02 (DEB 1266 2009-07-14)
MIME-Version:	1.0
X-Spam_score:	-1.9
X-Spam_score_int:	-18
X-Spam_bar:	-
X-Spam_report:	Spam detection software, running on the system "onesha.kyla.fi", has
	identified this incoming email as possible spam. The original message
	has been attached to this so you can view it (if it isn't spam) or label
	similar future email. If you have any questions, see
	the administrator of that system for details.
Reply-To:	geda-help AT delorie DOT com

 Content preview:  Hi, I'm designing board to be made at home. So vias and pins
    don't have plated holes. Also copper on component side is useless. This board
    is 2 sided, so I would get more space if pin's copper ring would not be on
    useless side. [...] 
 
 Content analysis details:   (-1.9 points, 5.0 required)
 
  pts rule name              description
 ---- ---------------------- --------------------------------------------------
 -0.0 NO_RELAYS              Informational: message was not relayed via SMTP
 -1.9 BAYES_00               BODY: Bayes spam probability is 0 to 1%
                             [score: 0.0000]
X-SA-Exim-Connect-IP: <locally generated>
X-SA-Exim-Mail-From: jaakko AT darkeagle DOT dy DOT fi
X-SA-Exim-Scanned: No (on darkeagle.dy.fi); SAEximRunCond expanded to false
X-Brightmail-Tracker: H4sIAAAAAAAAA+NgFrrKLMWRmVeSWpSXmKPExsUS1KQ+Uff/Di1/g5dLuCzW/H/J7MDocenZ
	F/YAxigum5TUnMyy1CJ9uwSujKXXTrEXXGCveHmvroFxMVsXIyeHhICJxJNZr6BsMYkL99YD
	2VwcQgL/GSUWHe1ghXCuMUo8XfuCBaSKRUBF4tf9k4wgNpuAi8SBG//Zuxg5OEQEJCXuHpQG
	MYUF/CW2f+MBqeAVcJRob2wCqxYV0JXY3L2UDSIuKHFy5hOwicwCfhLHVn5lhrAdJXYfesMG
	MkZCQEji+4V4iNNEJXZu2QZ1Jq/E2RkNTCCXSQjcZZeYeuUiO0RCU+LgpU0sELa2xNH/rxgh
	bG+J+wsvMk5gFJmFZPUsJKtnIVkNYZtJPHhxH6pGW+L+zTY2mJrT1/4zL2BkW8XIU5xbUmCk
	l1hZqZeWuYkRHBX2ITsYHz/RPsQowMGoxMO7sFbTX4g1say4MvcQowQHs5IIb6KTlr8Qb0pi
	ZVVqUX58UWlOavEhRiYOTqkGRqYHTFqtex/37Y2QtLoprPny8ZXWu0+zxdMevmwQ2pFv+n+K
	R+D87i+714TzrCnrNFr8Uo33mGqLc3RtQK+0VKf58hMNfx2kEgsvzlt1IVPN3J5zr8271f8U
	a33UFS6+OjG/ekvqYs3D9ksTN8iwiB/bNTOFM/lv5NxQDudJwVLxPToTT13QU2Ipzkg01GIu
	Kk4EAMmWue1oAgAA

  This message is in MIME format.  The first part should be readable text,
  while the remaining parts are likely unreadable without MIME-aware tools.

--8323328-1884838352-1328191173=:20247
Content-Type: TEXT/PLAIN; FORMAT=flowed; CHARSET=UTF-8
Content-Transfer-Encoding: QUOTED-PRINTABLE
Content-ID: <alpine DOT DEB DOT 2 DOT 02 DOT 1202021825212 DOT 21502 AT darkeagle DOT dy DOT fi>

Hi,

I'm designing board to be made at home. So vias and pins don't have plated=
=20
holes. Also copper on component side is useless. This board is 2 sided, so =
I=20
would get more space if pin's copper ring would not be on useless side.

I tried to make pin with 'hole' flag and putting pad with 'onsolder' at sam=
e=20
place. This makes ok layout, except rat optimization throughs million error=
s=20
(shorted pads and pins, line too close to hole, etc).

Is there any correct way to do this?

--
Jaakko Kantoj=C3=A4rvi
  jaakko AT darkeagle DOT dy DOT fi


--8323328-1884838352-1328191173=:20247--

- Raw text -