X-Authentication-Warning:	delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient:	geda-help AT delorie DOT com
Message-ID:	<20120104181905.20607.qmail@stuge.se>
Date:	Wed, 4 Jan 2012 19:19:05 +0100
From:	Peter Stuge <peter AT stuge DOT se>
To:	geda-help AT delorie DOT com
Subject:	Re: [geda-help] Query gschem and PCB designer
Mail-Followup-To:	geda-help AT delorie DOT com
References:	<CAF0dY_tG6hcjEJGWK_vW3FJgQFGaeZs5ndmQHOpyqc58FocnBQ AT mail DOT gmail DOT com> <201201031509 DOT q03F9ZFJ029642 AT envy DOT delorie DOT com> <CAF0dY_u5MwdVNz40+1oJD64b_QyR0_r-M4GXJhaZ_QjE=QH5Cw AT mail DOT gmail DOT com> <CAF0dY_suDUw9O8xxjDZdXz_5XEZaCkeAeGhMJ+8OwXM-i49XWA AT mail DOT gmail DOT com> <CACNnPRnhk__3ggSB-DpG1hJbfWA5GksowkKzb3kxvd+fnd=6fA AT mail DOT gmail DOT com> <CAF0dY_se8R1WSW956bUCZZD2mNiEBARDgMATEO-WtucJROFU5g AT mail DOT gmail DOT com> <CACNnPRknHMT5Q-LKG=_QeiDDkWxzsLWkXFRbv1jJOq4iyyuruA AT mail DOT gmail DOT com> <CAF0dY_uLDDP08--W8TWnycy2QyN3UbDX+KLTq_oBp=mnzqrY6g AT mail DOT gmail DOT com> <20120104132321 DOT 13981 DOT qmail AT stuge DOT se> <CAF0dY_uzTxv+HKgSP1M1iwFZnyE2yCWfEuauOihJgzaUK=bHaw AT mail DOT gmail DOT com>
MIME-Version:	1.0
In-Reply-To:	<CAF0dY_uzTxv+HKgSP1M1iwFZnyE2yCWfEuauOihJgzaUK=bHaw@mail.gmail.com>
Reply-To:	geda-help AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-help AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

Hi,

chetan patil wrote:
> On Wed, Jan 4, 2012 at 6:53 PM, Peter Stuge <peter AT stuge DOT se> wrote:
> > It will work, but maybe you will use the same type of power supply
> > connection in another project?
> 
> What is I make use of via or holes footprint at gedasymbols ?

There are two major differences between vias and a connector
footprint that I can think of right now:

1. Vias are covered by solder mask if the board has solder mask. This
   makes it inconvenient to connect something to them.

2. Vias are intended only for connecting different layers, not for
   outside connections.

You mentioned that your power supply connection uses "probes" but
I'm not exactly sure how they look, so unfortunately I can't make a
specific recommendation about what is best. If you explain the power
connection in more detail I think you will get more suggestions.


> Is it recommended to create things on own?

It's your choice. If someone else has created and uploaded a symbol
or footprint which you can reuse then I would reuse. Sometimes
symbols and footprints need to be customized, e.g. to compensate for
some parameters in the board fabrication process, and that usually
means that footprints have to be created locally, even if a footprint
for the same package was already uploaded by someone else.

If you find footprints which you can use then I would use those!

I think for all my designs I have used existing footprints for many
parts, but usually always needed to create some new footprints
myself for a few parts.


//Peter

- Raw text -