X-Authentication-Warning:	delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient:	geda-help AT delorie DOT com
DKIM-Signature:	v=1; a=rsa-sha256; c=relaxed/relaxed;
	d=gmail.com; s=gamma;
	h=mime-version:in-reply-to:references:from:date:message-id:subject:to
	:content-type;
	bh=DzFlT7qSzup0YbcOkZEGL/pELrqkTRZ8ZYlYt4t05Gc=;
	b=To3h90gXMPqsVdx+fKH3SKStQLYKI2F2syxEcxbqP/rLCrn4a2Yl5yJgAGGg36RpLQ
	bRJx5i+tbCUTVjfCTeImB+s+5ApQ39ZQpx8NevMUFgvrFIHfUEyac7cJ5oT9GU2C9Ed1
	IgxYjaMmthTHAdMHwW3XdeijkmaMiGqtdt61k=
MIME-Version:	1.0
In-Reply-To:	<CAF0dY_uLDDP08--W8TWnycy2QyN3UbDX+KLTq_oBp=mnzqrY6g@mail.gmail.com>
References:	<CAF0dY_vnw9VVaTwq0vAkKmrJOnbbk-NrMcFYAaoV+ak2svLdoA AT mail DOT gmail DOT com>
	<CACNnPR=5xUK=ptxwSUKrckSYkXHSqy+Vg_spQXBqeFz6Gyxcog AT mail DOT gmail DOT com>
	<CAF0dY_tZ28rybDEG=kXOK_FxpTHvgfTX0W5A7tqz8zc7QvdX=g AT mail DOT gmail DOT com>
	<201201031450 DOT q03Eov0Q028930 AT envy DOT delorie DOT com> <CAF0dY_tG6hcjEJGWK_vW3FJgQFGaeZs5ndmQHOpyqc58FocnBQ AT mail DOT gmail DOT com>
	<201201031509 DOT q03F9ZFJ029642 AT envy DOT delorie DOT com> <CAF0dY_u5MwdVNz40+1oJD64b_QyR0_r-M4GXJhaZ_QjE=QH5Cw AT mail DOT gmail DOT com>
	<CAF0dY_suDUw9O8xxjDZdXz_5XEZaCkeAeGhMJ+8OwXM-i49XWA AT mail DOT gmail DOT com>
	<CACNnPRnhk__3ggSB-DpG1hJbfWA5GksowkKzb3kxvd+fnd=6fA AT mail DOT gmail DOT com>
	<CAF0dY_se8R1WSW956bUCZZD2mNiEBARDgMATEO-WtucJROFU5g AT mail DOT gmail DOT com>
	<CACNnPRknHMT5Q-LKG=_QeiDDkWxzsLWkXFRbv1jJOq4iyyuruA AT mail DOT gmail DOT com> <CAF0dY_uLDDP08--W8TWnycy2QyN3UbDX+KLTq_oBp=mnzqrY6g AT mail DOT gmail DOT com>
From:	Abhijit Kshirsagar <abhijit86k AT gmail DOT com>
Date:	Wed, 4 Jan 2012 13:08:28 +0530
Message-ID:	<CACNnPR=u1-AMG_fere7Xh=sKudd7XWnd78O0wwx+sN8WEO__dA@mail.gmail.com>
Subject:	Re: [geda-help] Query gschem and PCB designer
To:	geda-help AT delorie DOT com
Reply-To:	geda-help AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-help AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

Yes it will work.

If I understand correctly, you are using PCB directly - without the
use of schematic?


~Abhijit




On Wed, Jan 4, 2012 at 13:03, chetan patil <chtpatil AT gmail DOT com> wrote:
> Hi Abhijit,
>
> On Wed, Jan 4, 2012 at 12:40 PM, Abhijit Kshirsagar <abhijit86k AT gmail DOT com>
> wrote:
>>
>> I see from your schematic that your circuit needs a 6Volt source but
>> there is no symbol for it - so it will not be there in the PCB.
>>
>> Usually one would add a symbol like a power jack or any other two pin
>> connector to connect a battery or a power supply.
>> (See
>> http://www.cedt.iisc.ernet.in/people/students/kabhijit/files/.gEDA/flasher-1v2.sch)
>
>
>
> Thank You for the inputs. I got ti.
>
> As I'm using PCB application directly. So I have added a VIA for vcc and
> gnd.
> So the probes can be inserted directly on to that.
>
> I think it should work ?
>
> --
> Thank You and Warm Regards,
>
> Chetan Arvind Patil,
> www.chetanpatil.info
>
>
>

- Raw text -