Mail Archives: djgpp/2014/12/27/22:55:30
This is a port of GNU binutils 2.25 to MSDOS/DJGPP.
The GNU binutils are utilities of use when dealing with binary files, either
object files or executables. These tools consist of the linker (ld), the
assembler (gas), and the profiler (gprof). There is also a collection of
other binary tools, including the disassembler (objdump). These tools make
use of a pair of libraries (bfd and opcodes) and a common set of header files.
DJGPP specific changes.
=======================
- This port allows a maximal number of 4294967296 relocations per object file
and a maximal number of 4294967296 of lines per executable file.
The previous limits were the classical COFF limitations of 65536 for boths.
Please note, that due to limitations inherent to DOS and memory ressources
not every file can be compiled. E.g.: to be able to compile a single file
containing up to 3 * 65536 relocations I had to increment stack space of
cc1.exe from 2MB to 10MB. If the file contains 4 * 65536 relocations then
cc1.exe aborts because memory has become exhausted. Neither as.exe nor
ld.exe have shown memory issues. Both have the standard stack space of
512KB. In other words, even if 32 bit values for relocation and line
counters are now supported by DJGPP port of as.exe and ld.exe it does not
imply that large files can be successfully compiled and linked. There are
memory limitations that may not be solvable.
OFYI how the DJGPP specifc support for number of relocations greater than
64K works:
- If the number of relocations of an object file exceeds 65534 then
s_nreloc in the section header is set to 65535 to signal the overflow
and the real number of relocations is stored in an extra COFF relocation
directive. This is always the first relocation directive in the sequence
of relocation directives of this object file. The 32 bit field r_vaddr
is used to store the real number of relocations. This extra relocation
directive is later removed. To signal this overflow also the
STYP_NRELOC_OVFL bit (0x01000000) is set in the s_flags field of the
section header.
- If the number of lines of an object file exceeds 65535 then the assembler
will abort with an error message. This can only happen if COFF debug info
is used. There is no work around for this issue.
- When the linker creates an executable file from the objects files and
the total number of lines exceeds 65535 the lower 16 bit of that value
will be stored in the s_nlnno field and the higher 16 bit in the s_nreloc
field of the section header of the executable file. This can only happen
if COFF debug info is used.
- The linker script changes, are based on the diff files taken from Andris
Pavenis' bnu219s2.zip and djcross-binutils-2.19.1-10ap.src.rpm. Both are
available at ftp.delorie.com and mirrors.
I have only made those adjustments necessaries to get those patches fit with
the current source files.
- The diffs file that contains all changes I have done is stored in the /djgpp
directory. Also in this directory is stored the small build.sh script that
I have used to adjust all configure and libtool scripts of the package. The
well known issues that must been fixed are that:
1) the gawk test for setting the CR coding to be used does not work at all.
2) inhibit that gawk prepends a leading slash to DOS style path names.
3) a libtool function needs to be adjusted to get the install target
working.
4) the target alias is removed from the tooldir and scriptdir path to get
the programs and linker scripts installed in the canonical places of a
DJGPP installation.
That script is very simple and will only work to configure and compile the
sources in the /djgpp directory. If you want to make changes or pass more
or other options to configure, you will have to edit it or write your own
script. build.sh shall not be smart, it shall only DTRT.
- The linker script has been adapted to discard LTO sections created by the
compiler if the -flto flag is passed to the compiler. This is due to LTO
specific file names that are not 8.3 clean especially if the -save-temps
option is used. This may change in the future when the djgpp port of the
compiler fully supports LTO.
- This port provides a version of the linker that will be capable to resolve
multiple symbol definitions conflicts when using DXE3 modules. Multiple
symbol definition always occur when an application is linked with various
libraries and more than one of its provides an object file defining the
same function (symbol). E.g.: when compiling an arbitrary GNU source
package like grep with NLS enabled and using the DXE3 module versions of
the iconv library and the gettext library, a definition of the locale_charset
function (aka symbol) will appear three times. One definition (aka
function implementation) will be provided by the grep code itself via its
own code (aka libgreputils.a). The other two will be provided by the import
libraries libiconv.a and libintl.a of both DXE3 modules used. The linker
will note that the different libraries provide different implementations of
the same function and will abort operation with an error message like this:
c:/djgpp-2.04/lib/libintl.a(dxe_tmp.o):dxe_tmp.c:(.text+0x7a4): multiple definition of `locale_charset'
../lib/libgreputils.a(localcharset.o):h:/g/srcs/gnu/grep-2.18/_build.204/lib/.././../lib/localcharset.c:363: first defined here
c:/djgpp-2.04/lib/libiconv.a(dxe_tmp.o):dxe_tmp.c:(.text+0x248): multiple definition of `locale_charset'
../lib/libgreputils.a(localcharset.o):h:/g/srcs/gnu/grep-2.18/_build.204/lib/.././../lib/localcharset.c:363: first defined here
collect2.exe: error: ld returned 1 exit status
In case of multiple symbol definitions, the linker will check if one of the
definitions comes from an import library (all import libraries contain only
one single object file called dxe_tmp.o). If the symbol definition is stored
in a file called dxe_tmp.o, all other definitions will be ignored/discarded.
This means that the symbol definition of the DXE3 module has __always__
precedence over any other symbol definition. This will guarantee that all
compiled programs that use the same DXE3 module will use at runtime the
same implementation of the required function and not a particular
implementation provided by the sources of the program being compiled. That
implementation may not even have been ported to djgpp and thus will be
useless at all. There is no linker switch to change this behavior and to
give any other function implementation precedence over the DXE3 implementation.
If more than one import library provides a definition for the same symbol,
always the first is used and all other import library definitions are ignored.
This is not an issue because the import libraries only provide wrapper
functions that call at runtime the real functions stored in the DXE3 modules
and these wrapper functions look all the same. Without this capability,
the DXE3 modules become almost useless for NLS support, because the porter
of every package that has NLS enabled would have to take care to remove all
NLS specific functions from the port code that are already provided either
by the gettext library or by the iconv library. Please note that the linker
cannot resolve any other multiple symbol definition conflict than the one
described for the DXE3 modules. Of course, if static library versions of
those NLS libraries are used, these symbol conflicts do not arise at all
and the linker creates an executable in the usual way.
The linker version with this feature has been compiled using a freshly
compiled version of libc.a from the CVS repository. You can download
an archive of the repository tree at:
<http://www.ludd.luth.se/~ams/djgpp/cvs/djgpp.cvs.tar.gz>
To be able to compile the linker with this feature you must uncomment
the line that defines the DXE3_SUPPORT_ENABLED variable in the
/djgpp/build.sh file.
- There are ports like the one of GNU gettext that provide libraries with
file names that cannot be uniquely mapped to short file names without
using numeric tails. Usually in this case the files are renamed so they
have a valid short file name without having to use numeric tails. The
consequence of this renaming is that a lot of Makefiles need to be
adjusted in a DJGPP/DOS specific way. To avoid this inconvenience, this
version of the linker will provide a mapping feature between the original
long file names and the DOS specific short file names. This port provides
a new file called libnames.tab located in /dev/env/DJDIR/lib. When the
linker tries to open a library with its original name and fails, it will
try to open /dev/env/DJDIR/lib/libnames.tab and load it content into a
static array/table. With the aid of this table it will try to map the
long file name to a short file name. If this mapping is successful it
will try to load that file instead of the original one and if this was
also succesfull it will continue working. For every other library that
cannot be loaded by its original name, the linker will search for an
alternative name in the array/table and load that library instead. Please
note that you cannot specific the location of libnames.tab. If required,
the linker will load it from the canonical location and there will be no
error message if libnames.tab cannot be found or loaded. If the linker
cannot load the library neither by its original name nor by its short
name it will abort the operation in the usual way and issue an error
message about file loading error printing the original file name.
The syntax for the entries is quite simple and the scanning/reading of
the file is not bullet-proof. This means that syntax errors will not be
detected and will produce nonsense file name translations that will very
likely make abort the linker. I do not think that this is a great
inconvenience because most of the users should never add any entry to
this file. It is the job of the port of some package that must provide
an update of libnames.tab if his port contains renamed libraries.
Syntax of libnames.tab entries:
1) The # character defines comment line that will be skipped.
The comment is the complete line and NOT only the text following the
# character!
2) Empty lines will be skipped.
3) A valid entry looks like:
withverylongname-1.2 wvln12
Neither the prefix nor the suffix/extension of the library name is
part of the table entry. For the above example the complete file
name of the library would be:
libwithverylongname-1.2.a
To get a valid entry strip the prefix "lib" and the suffix ".a" from
the library name. The same applies to the short file name of the
library. In the example above, the library has been renamed to:
libwvln12.a
and that is the file name of the library that the linker will use.
The original file name is always the first name and the substitute
file name is the second name. Both names are separated by at least
one space or tab character.
Another example: the gettext port provides a library that has been
renamed to libgtxtsrc.a. Its original name was libgettextsrc.a.
The entry for this library looks like this:
gettextsrc gtxtsrc
As can be seen the "lib" prefix and the ".a" suffix have been stripped
from both library names to get the table entry. In the actual version
of libnames.tab there are only the three entries for the three renamed
libraries provided by the gettext port.
- For performance reasons, BFD tries to open and cache certain amount of
files and its contents. How many files can be opened is determinated at
program start using the getrlimit function. Unfortunately this function
seems to be a placebo function. At least when using djdev204 on WinXP,
this function always returns the hard coded value of 255. This is the
value for the number of files that can be opened (RLIMIT_NOFILE). BFD
takes one eight of this value but at least 10 and opens so mutch files
as required. If your FILES entry in config.sys is not large enough (at
least around 35) then the program aborts. The corresponding BFD function
now assumes that there are at least 15 available and will use all of them
if required. This has the consequence that the user must set his FILES
entry in config.sys or config.nt to 20 or 25. The value depends on how
much file handles the OS and the DPMI server has already consumed for its
on needs.
- The port has been configured and compiled on WinXP SP3. There is no
guarantee that this may be possible with any other DOS-like OS. Due
to the massive use of long file names it will not be possible to configure
and compile without LFN support.
- The DJGPP 2.04 version of the port has been compiled using gcc492 and
bnu224br2. But instead of using the libc.a provided djdev204, a libc
version compiled from the repository code has been used. The repository
code has been patched with the memory patch as provided by Andris Pavenis
in:
http://ap1.pp.fi/djgpp/djdev/djgpp/20140421/use_nmalloc.diff
The goal is to test how well the new memory system and the current libc
code works. The repository code can be downloaded from Martin Stromberg's
site as:
http://www.ludd.luth.se/~ams/djgpp/cvs/djgpp.cvs.tar.gz
- To be able to configure and compile on WinXP using djgpp 2.03 it will be
necessary to replace cat.exe and sort.exe with the versions compiled with
djgpp 2.04.
As usual, all djgpp specific files (build.sh, diffs, README files, etc.)
are located in the /djgpp directory. The sources have not been configured
so you must change into the /djgpp directory and start build.sh. This will
configure the sources and start make.
For further information about Binutils please read the info docs and NEWS file.
The port consists of the usual four packages that have been compiled
using stock djdev203 and that can be downloaded from ftp.delorie.com
and mirrors as (time stamp 2014-12-24):
GNU binutils 2.25 binary and info format documentation:
ftp://ftp.delorie.com/pub/djgpp/current/v2gnu/bnu225b.zip
GNU binutils 2.25 bfd, liberty and opcode libraries and headers:
ftp://ftp.delorie.com/pub/djgpp/current/v2gnu/bnu225a.zip
GNU binutils 2.25 dvi, html, ps and pdf format documentation:
ftp://ftp.delorie.com/pub/djgpp/current/v2gnu/bnu225d.zip
GNU binutils 2.25 source:
ftp://ftp.delorie.com/pub/djgpp/current/v2gnu/bnu225s.zip
The binaries and library have been produced a second time using a libc.a
version compiled from current repository code and patched with the new
malloc code. This package is available at ftp.delorie.com and mirrors
as (time stamp 2014-12-24):
GNU binutils 2.25 binary and info format documentation:
ftp://ftp.delorie.com/pub/djgpp/beta/v2gnu/bnu225b.zip
GNU binutils 2.25 bfd, liberty and opcode libraries and headers:
ftp://ftp.delorie.com/pub/djgpp/beta/v2gnu/bnu225a.zip
Send binutils specific bug reports to <bug-binutils AT gnu DOT org>.
Send suggestions and bug reports concerning the DJGPP port to
comp.os.msdos.djgpp or <djgpp AT delorie DOT com>.
Enjoy.
Guerrero, Juan Manuel <juan DOT guerrero AT gmx DOT de>
- Raw text -