X-Recipient:	archive-cygwin AT delorie DOT com
X-SWARE-Spam-Status:	No, hits=-2.1 required=5.0 tests=AWL,BAYES_00,DKIM_SIGNED,DKIM_VALID,DKIM_VALID_AU,RP_MATCHES_RCVD,TW_UV,TW_VF,TW_VZ,TW_XV
X-Spam-Check-By:	sourceware.org
X-DKIM:	Sendmail DKIM Filter v2.8.3 mux2.uit.no pAA9t7C3070618
From:	=?utf-8?B?RWR2YXJkc2VuIEvDpXJl?= <kare DOT edvardsen AT uit DOT no>
To:	"cygwin AT cygwin DOT com" <cygwin AT cygwin DOT com>
Subject:	Re: What updates done after October 3 may affect gfortran built binaries?
Date:	Thu, 10 Nov 2011 09:55:06 +0000
Message-ID:	<1320918860.13045.95.camel@kare-desktop>
MIME-Version:	1.0
Mailing-List:	contact cygwin-help AT cygwin DOT com; run by ezmlm
List-Id:	<cygwin.cygwin.com>
List-Subscribe:	<mailto:cygwin-subscribe AT cygwin DOT com>
List-Archive:	<http://sourceware.org/ml/cygwin/>
List-Post:	<mailto:cygwin AT cygwin DOT com>
List-Help:	<mailto:cygwin-help AT cygwin DOT com>, <http://sourceware.org/ml/#faqs>
Sender:	cygwin-owner AT cygwin DOT com
Mail-Followup-To:	cygwin AT cygwin DOT com
Delivered-To:	mailing list cygwin AT cygwin DOT com
X-MIME-Autoconverted:	from base64 to 8bit by delorie.com id pAA9tTaB020725

> Thanx a lot, Marco for takng time!
> 
> In order to replicate my build you need to install latest version of the
> grib_api library
> (http://www.ecmwf.int/products/data/software/download/grib_api.html)
> and istall it with jasper
> 
> tar xvfz grib_api-1.9.9.tar.gz
> ./configure [--with-jasper=<jasper path>]
> make
> make install
> 
> You then have to edit the makefile.ecmwf_gfortran_32 to have the right
> lib and include path's set for gfortran to find jasper and grib_api. The
> path's found in makefile.ecmwf_gfortran_32 are just showing where the
> programmers installed those lib's before distributing the FLEXPART
> software.
> If you get a successful build, it will still prompt an error since you
> will still miss some expected settings, but you will clearly see whether
> this is a bad binary or not.
> 
> I will definitely try reinstalling an older version of binutils and give
> it a try.
> 
> Thanx again for the advice.
> 
> Regards,
> KÃre
> 
I forgot to say that the file includepar in the FLEXPART folder need to
be edited to look like this in the section:

**********************************************
C Maximum dimensions of the input mother grids
**********************************************

      integer nxmax,nymax,nuvzmax,nwzmax,nzmax,nxshift
      parameter(nxmax=361,nymax=181,nuvzmax=92,nwzmax=92,nzmax=92)
c     parameter(nxmax=361,nymax=181,nuvzmax=61,nwzmax=61,nzmax=61)
c     parameter(nxmax=721,nymax=361,nuvzmax=27,nwzmax=27,nzmax=27)
      parameter(nxshift=359)  ! for ECMWF
c     parameter(nxshift=0)    ! for GFS
      integer nconvlevmax,na 
      parameter (nconvlevmax = nuvzmax-1)
      parameter (na = nconvlevmax+1)



otherwise you will get a crash with some error messages during the make
procedure.

Thanx,
KÃ¥re

- Raw text -