X-Recipient:	archive-cygwin AT delorie DOT com
X-SWARE-Spam-Status:	No, hits=3.1 required=5.0 tests=BAYES_20,MSGID_SPAM_CAPS
X-Spam-Check-By:	sourceware.org
X-IronPort-Anti-Spam-Filtered:	true
X-IronPort-Anti-Spam-Result:	AtoMAImet0ukDzvj/2dsb2JhbACCMI0jizuBLrEdgmkIghYE
From:	Robrecht Dewaele <Robrecht DOT Dewaele AT vub DOT ac DOT be>
To:	cygwin AT cygwin DOT com
Date:	Sun, 04 Apr 2010 05:56:23 +0200
X-sender-IP:	134.184.49.30
Subject:	Re: unable to set icrnl (stty -F /dev/ttyS2 icrnl) for an ftdi device
Message-Id:	<IHEEAAIAAAHAHAAH@webmail.ulb.ac.be>
Mailing-List:	contact cygwin-help AT cygwin DOT com; run by ezmlm
List-Id:	<cygwin.cygwin.com>
List-Subscribe:	<mailto:cygwin-subscribe AT cygwin DOT com>
List-Archive:	<http://sourceware.org/ml/cygwin/>
List-Post:	<mailto:cygwin AT cygwin DOT com>
List-Help:	<mailto:cygwin-help AT cygwin DOT com>, <http://sourceware.org/ml/#faqs>
Sender:	cygwin-owner AT cygwin DOT com
Mail-Followup-To:	cygwin AT cygwin DOT com
Delivered-To:	mailing list cygwin AT cygwin DOT com

On 4/3/2010 5:55 PM, Robrecht Dewaele wrote:
>> I'm using cygwin 1.7.2 on Windows 7, and I am unable to set the icrnl flag for >> /dev/ttyS2 as shown at the bottom of my message. The device attached to ttyS2 is a ARM development board which uses an ftdi chip for serial communication over USB.
>> (The device is connected with USB, and the driver creates a virtual com port.)

> Are you running them as Administrator? (UAC or no UAC, this matters.)
> --
> ~
> Morgan Gangwere

Yes, the user account I'm running this on is an administrator account.
Running cygwin as administrator (with right-click, run as ...) does not change
the behavior.

I must add that I am able to successfully change the baud rate, but not able to
change most of the other flags. Changing icrnl does not render an error, but
still nothing changed (see below).

(this is on a Windows 7 VM, other HW is the same)
robbe AT eagle764 ~
$ stty -F /dev/ttyS2 onlcr

robbe AT eagle764 ~
$ stty -F /dev/ttyS2
speed 9600 baud; line = 0;
intr = <undef>; quit = <undef>; erase = <undef>; kill = <undef>; eof = <undef>;
swtch = <undef>; susp = <undef>; rprnt = <undef>; werase = <undef>;
lnext = <undef>; flush = <undef>; min = 0; time = 0;
-cread
-brkint -icrnl -imaxbel
-opost -onlcr
-isig -icanon -iexten -echo -echoe -echok -echoctl -echoke

--
Problem reports:       http://cygwin.com/problems.html
FAQ:                   http://cygwin.com/faq/
Documentation:         http://cygwin.com/docs.html
Unsubscribe info:      http://cygwin.com/ml/#unsubscribe-simple

- Raw text -