Mail Archives: cygwin/2000/08/09/18:04:54
Hi Markus,
then I bet you have two incompatible versions of cygwin1.dll on your
system.
Bye, Heribert (heribert_dahms AT icon-gmbh DOT de)
> -----Original Message-----
> From: Markus Hoenicka [SMTP:Markus DOT Hoenicka AT uth DOT tmc DOT edu]
> Sent: Wednesday, August 09, 2000 18:41
> To: Andre Bleau
> Cc: cygwin AT sources DOT redhat DOT com
> Subject: Re: _ctype_ not found in cygwin1.dll
>
> Hi,
>
> this sounds reasonable and was mentioned in the archives a while
> ago. I was just confused by the fact that I can run the standalone app
> without problems. It just bites me if I run it as a service. I rather
> thought that I'd have to do some special tricks to run CygWin apps as
> a
> service.
>
> So for the next weeks (months?) I'll be mulling over libmysqlclient.a
> ...
>
> Thanks
> Markus
>
> Andre Bleau writes:
> > After I upgraded to Cygwin 1.1.x I had the same problem while
> linking with
> > a library I compiled under Cygwin B20.1. Some function inside the
> library
> > was including <ctype.h> for the use of isupper, islower... These
> are macros
> > using a
> > global variable of the cygwin library named _ctype_ whose
> declaration in
> > ctype.h has changed between B20.1 and 1.1.x to now include the
> > __declspec(dllimport) attribute. You will have to recompile the
> modules of
> > your libmysqlclient.a that include <ctype.h>.
> >
> > Hope this helps.
> >
> > >Hi all,
> > >
> > >this is sort of a follow-up to my previous problem (accept() fails
> if
> > >I run my app as service, but succeeds if I run it standalone).
> > >
> > >I found out that my app does run fine as a server on a different
> B20.1
> > >installation. So I figured that my CygWin setup may be screwed up
> and
> > >started from scratch. I upgraded to the latest net release and
> rebuilt
> > >my app completely (except for libmysqlclient.a: This was compiled
> with
> > >B20.1, and I could not yet figure out how to compile it on 1.1.4).
> > >
> > >Now I face a different problem. My app again runs just fine as
> > >standalone, but when I try to start it as a service (using
> > >invkr153.zip) I get:
> > >
> > >"The procedure entry point _ctype_ could not be located in the
> dynamic
> > >link library cygwin1.dll"
> > >
> > >What is this trying to tell me? Any help will be greatly
> > >appreciated. cygcheck is attached below.
> > >
> > >Markus
> >
> >
> > André Bleau, ing., analyste
> > bleau AT courriel DOT polymtl DOT ca
> >
> > Département de génie électrique et Electric Engineering and
> > de génie informatique Computer Engineering
> department
> > École Polytechnique de Montréal Montreal Polytechnic
> School
> >
>
> --
> Markus Hoenicka, PhD
> UT Houston Medical School
> Dept. of Integrative Biology and Pharmacology
> 6431 Fannin MSB4.114
> Houston, TX 77030
> (713) 500-6313, -7477
> (713) 500-7444 (fax)
> Markus DOT Hoenicka AT uth DOT tmc DOT edu
> http://ourworld.compuserve.com/homepages/hoenicka_markus/
>
>
> --
> Want to unsubscribe from this list?
> Send a message to cygwin-unsubscribe AT sourceware DOT cygnus DOT com
--
Want to unsubscribe from this list?
Send a message to cygwin-unsubscribe AT sourceware DOT cygnus DOT com
- Raw text -