Mailing-List:	contact cygwin-help AT sourceware DOT cygnus DOT com; run by ezmlm
List-Subscribe:	<mailto:cygwin-subscribe AT sourceware DOT cygnus DOT com>
List-Archive:	<http://sourceware.cygnus.com/ml/cygwin/>
List-Post:	<mailto:cygwin AT sourceware DOT cygnus DOT com>
List-Help:	<mailto:cygwin-help AT sourceware DOT cygnus DOT com>, <http://sourceware.cygnus.com/ml/#faqs>
Sender:	cygwin-owner AT sourceware DOT cygnus DOT com
Delivered-To:	mailing list cygwin AT sourceware DOT cygnus DOT com
X-Authentication-Warning:	skarn.sonusnet.com: tgoodman set sender to tsg AT bonedaddy DOT net using -f
Date:	Tue, 27 Jun 2000 16:37:07 -0400
From:	Todd Goodman <tsg AT bonedaddy DOT net>
To:	Jonas Jensen <bones0_list AT hotmail DOT com>
Cc:	Todd Goodman <tsg AT bonedaddy DOT net>,
	Cygwin list <cygwin AT sourceware DOT cygnus DOT com>
Subject:	Re: Using glib(c) and gtk+ in Cygwin
Message-ID:	<20000627163707.N9184@skarn.sonusnet.com>
References:	<20000627152845 DOT 24963 DOT qmail AT hotmail DOT com> <20000627114505 DOT G9184 AT skarn DOT sonusnet DOT com> <20000627202946 DOT 31976 DOT qmail AT hotmail DOT com>
Mime-Version:	1.0
User-Agent:	Mutt/1.2i
In-Reply-To:	<20000627202946.31976.qmail@hotmail.com>; from bones0_list@hotmail.com on Tue, Jun 27, 2000 at 07:41:22PM +0200
X-Editor:	Vim-506 http://www.vim.org/

* Jonas Jensen <bones0_list AT hotmail DOT com> [000627 16:30]:
> Thanks for helping, but it still doesn't work properly...
> 
> > You need to tell it not to use threading (or get the pthread lib from
> > http://sourceware.cygnus.com).  I think the configure command to disable
> > threading is --enable-thread=no (try ./configure --help).
> I tried disabling it, and now glib compiles... but it doesn't seem to work right,
> because I can't compile gtk+. When I run ./configure on gtk+, it says:

Did you install glib?  It's looking for a script (glib-config) that is
in your PATH and when run with --version prints the latest version.

If you type 'glib-config --version' do you get a version number?  Is it
>= 1.2.8?

You have a pretty new version of GTK+.  I have only built glib and
GTK 1.2.7.

> 
> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
> checking for GLIB - version >= 1.2.8... no
> *** Could not run GLIB test program, checking why...
> *** The test program failed to compile or link. See the file config.log for the
> *** exact error that occured. This usually means GLIB was incorrectly installed
> *** or that you have moved GLIB since it was installed. In the latter case, you
> *** may want to edit the glib-config script: /usr/local/bin/glib-config
> configure: error:
> *** GLIB 1.2.8 or better is required. The latest version of GLIB
> *** is always available from ftp://ftp.gtk.org/.
> <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
> 
> I went looking for the "pthread" lib, but I only found a Win32 version. Is that
> the one I'm supposed to use? It comes with a .lib file and a few .h files... what
> do I do with those? Or do I need another version of that lib?

I'd recommend *not* using pthreads at all (or at least until the above
problems are cleared up).

Regards,

Todd

--
Want to unsubscribe from this list?
Send a message to cygwin-unsubscribe AT sourceware DOT cygnus DOT com

- Raw text -