Mail Archives: cygwin/2000/04/23/02:20:33
Following up on the exchange below, I find I can't change / back from text
to binmode, mainly because I can't unmount it, even though umount doesn't
complain:
c:\>umount /
c:\>mount
Device Directory Type Flags
c:\cygnus\usr /usr user binmode
c:\cygnus\bin /usr/bin user binmode
c:\cygnus\lib /usr/lib user binmode
\\.\tape0: /dev/st0 user textmode
\\.\tape1: /dev/st1 user textmode
\\.\a: /dev/fd0 user textmode
\\.\b: /dev/fd1 user textmode
C: / user textmode
c:\>
How can I change / from textmode back to binmode if I want to do so?
Thanks.
Richard Stanton
> -----Original Message-----
> From: Richard Stanton [mailto:stanton AT haas DOT berkeley DOT edu]
> Sent: Saturday, April 22, 2000 11:55 PM
> To: Tim Prince
> Cc: Cygwin Mailing List
> Subject: RE: New net release - problems with make and gdb
>
>
> That was it. Thanks.
>
> After installing the new release, c: was mounted (as /) in
> binmode, whereas previously it had been mounted in text mode.
> Changing the mount back to textmode allows make to run properly.
>
> Having said all that, I get the impression from this group that I
> "ought" to be mounting everything in binmode. Is this correct? If so, why?
>
> Thanks a lot.
>
> Richard Stanton
>
>
> > -----Original Message-----
> > From: Tim Prince [mailto:tprince AT computer DOT org]
> > Sent: Saturday, April 22, 2000 11:18 PM
> > To: Richard Stanton; cygwin AT sourceware DOT cygnus DOT com
> > Subject: Re: New net release - problems with make and gdb
> >
> >
> > That too looks like some mixup relative to binary and text
> > mounts. I managed to introduce text mounts where there were
> > none on my first installation attempt. Again on my third
> > attempt, trying to install under W95 on a dual boot machine with
> > the net release already installed successfully on NTFS under
> > W2K. But on the working installation I haven't seen any make
> > failures, using makefiles which never ran consistently before in
> > any form of Windows.
> >
> > ----- Original Message -----
> > From: "Richard Stanton" <stanton AT haas DOT berkeley DOT edu>
> > To: <cygwin AT sourceware DOT cygnus DOT com>
> > Sent: Saturday, April 22, 2000 10:35 PM
> > Subject: New net release - problems with make and gdb
> >
> >
> > > I've just installed the new net release. Two problems so far:
> > >
> > > 1) gdb - minor: If I type, at the command line, "gdb
> > progname", nothing
> > > seems to happen. It works OK in an EMACS window. Also, why is
> > the gdb
> > > program/archive so huge?
> > >
> > > 2) make - major, as it means all my makefiles don't work: I
> > have a makefile
> > > that starts:
> > >
> > > DEBUGFLAG= 0
> > >
> > > ifeq ($(DEBUGFLAG),1)
> > > CFLAGS= -Wall -g -mno-cygwin -I/projects/h
> > > [etc.]
> > >
> > > This used to run fine under the old release, but now when I
> > run make I get
> > > the error messages:
> > >
> > > c:\projects\xll>make rhs.xll
> > > makefile:6: Extraneous text after `ifeq' directive
> > > makefile:10: Extraneous text after `else' directive
> > > makefile:14: Extraneous text after `endif' directive
> > > makefile:30: *** commands commence before first target. Stop.
> > >
> > > Note: line 6 is the one with the ifeq command in it.
> > >
> > > Richard Stanton
> > >
> > >
> > > --
> > > Want to unsubscribe from this list?
> > > Send a message to cygwin-unsubscribe AT sourceware DOT cygnus DOT com
> > >
> >
> >
--
Want to unsubscribe from this list?
Send a message to cygwin-unsubscribe AT sourceware DOT cygnus DOT com
- Raw text -