X-Authentication-Warning: delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient: geda-help AT delorie DOT com
To: geda-help AT delorie DOT com
From: "Mittermayr Thomas (t DOT mittermayr AT gmx DOT at) [via geda-help AT delorie DOT com]" <geda-help AT delorie DOT com>
Subject: [geda-help] how to do rubout zone
Message-ID: <e27cbae3-ff23-f9bd-087c-86b410a5aab4@gmx.at>
Date: Thu, 28 Jul 2016 17:27:09 +0200
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:45.0) Gecko/20100101
 Thunderbird/45.2.0
MIME-Version: 1.0
Content-Type: text/plain; charset=utf-8; format=flowed
Content-Transfer-Encoding: 7bit
X-Provags-ID: V03:K0:wTJHTHD/z76iv207qSsv47ZmERewxySV8voSIlieQj18f8zaSWF
 YnYBo+4bHew860SJfVQ/knGhIqLa48rMSdCTPEWKv7p5TfT+mpZcla1FqSkr3vxa/WoZAiq
 /yXowlZJGoo+MaZF/6pwr3Y0NgWrmRX4xge2v8+7WfI7qVNTLZvfKUeBLYHFyzdYrh/Nzht
 bVceHRszGmanvVeft1QJA==
X-UI-Out-Filterresults: notjunk:1;V01:K0:eBEAgFYJywg=:6qqTOxSGkd11JaWkr4koyY
 5FdRopGN/Vn1v3KO/C9XJ2wIVfvE1puZ1xQbvI/Er42+NLiOBoFhhAVFut2P6d+WI7jnVDEMO
 o+vOHzYnkRZH7Hf7nYKDh3g2TjROgcP00CoZbOVs/JLo2kXpDZW+C6cAb363XwU+zq8cGt+Mh
 AaVzHLPikXMl8jZryix8wmsyYq+DF3etLvNEzrU72bpj9ymNJvZTfSR2yqRy9ozZZNvoTwdkD
 CQ98Za2O+iT1uLL/12zKudtCiKzXszy72I4YpxvGZxkXoLrr6CUzXiJiO7Gw01dqjOAFkN6ch
 bwb/oX4j0ropSPPGXUZP+hyJr1Ph+6nocvvsGLMLNLJfl9M6UHGdFIsSj8lxXSn++lHJWG9Dy
 xAXPKmR5Va9DxZ/tWo/TqYLskoBVVckW00SxiHpyH8PMEKb4DYu4/cwqJysdfssvELrpwVFgn
 FZAaOjVtwqBenVdfcGDOZN03DUQlHz1XBNI+eugy3kNzWxK/6HwvWpzmaqKB4sIdteZjhmoxg
 iuqBA2U6hdCMPNPPO/yCws25ODpQi0VKTqYhwo2KlDLGkmhKoM4zjlVjQsKRxXzQYP1iqW7Lo
 zusjPGOoN4CwQc2O677tJgrVPDVrJEiNMcliudHP12QzX8fXlzs+I3EbpMPuVkWCuCcqZBG/W
 9bzZKSDDwbVR2V5HY/9fsOz3m8FXK5cTKz1a5FIIB3uGPM60u2nk2+YyQ9q+G0/l/B+/AmygG
 ZfoijCQ9lmh05sGhMBaocym+5K5zwLgMFuvHMWmUthJOnHm5s0SaFprf2NWlVyhUL5kIAgggi
 diVGx7n
Reply-To: geda-help AT delorie DOT com

Hi list,

i need to create a footprint, that will place a rubout zone inside a 
component for our milling machine. I'm having problems to create a 
rubout zone because it would have to change the layer according to the 
actual pcb-side it is placed. If the component is on the top layer it 
should be on the rubout-layer-top, if the component is placed on the 
other side of the board it should be on the rubout-layer-bottom. How to 
achieve this.

btw: i like gEDA a lot, only the amount of useful tutorials is very 
"sparse" to say least...
-- 
thx
Th.M.