delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2019/05/20/04:22:16

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
X-Original-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; t=1558340380;
s=strato-dkim-0002; d=q40.de;
h=In-Reply-To:Date:Message-ID:From:References:To:Subject:
X-RZG-CLASS-ID:X-RZG-AUTH:From:Subject:Sender;
bh=Wi+hyqg56OvLG7/IFLiN7U0NZi3T03w5NQoCeeSOkRw=;
b=Lgx4ceNkcIbZERuJlZzu0Qp2KLDsFFQceJpUbzSg7T8TZ3KCbeVkyfbPxnD4dIPomU
GozvOLK2qZiKVHq7CbCHUbq/ZIcnZlmn7kHziZJdDCcMXOmfAqfomLdc81bwWTqhsVe8
FkE+F2VGlXFeuMQLpBCh34LWAcAXAuSxBBrqofZR3L9aRWOv1BWqwB8vKNT1HwWP9Jhq
tJcpIK2S2gQy0TqAMXOXHGmabd6wXVFFJVwlirpRTj8vvxQREIiF0GkRiODsSNKq5ZLH
BEPgXym8sIhz4KxED+87oMj05FmHKTrCfDiT7sL2ECPNISRj7mzinQQPY83IPLb7Sw5R
ZhOQ==
X-RZG-AUTH: ":KGkWcEuIaqvXDP/lM1VHWdKIkA3Ju5YmsfNOVu4RNhF4KSfc3vbqa34OhHVE"
X-RZG-CLASS-ID: mo00
Subject: Re: [geda-user] RS-274D Gerber Conversion
To: geda-user AT delorie DOT com
References: <e226233c-616a-e5f0-9689-1b9080b3e7ad AT q40 DOT de>
<CAHUm0tMrVKhrosLau0vz_CVsYF5N0qFjqz2HUM-n4kfs+kWWKw AT mail DOT gmail DOT com>
From: "Derek Stewart (derek AT q40 DOT de) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Message-ID: <c1d08d24-fb76-a524-ad55-82929e317729@q40.de>
Date: Mon, 20 May 2019 09:19:37 +0100
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:60.0) Gecko/20100101
Thunderbird/60.6.1
MIME-Version: 1.0
In-Reply-To: <CAHUm0tMrVKhrosLau0vz_CVsYF5N0qFjqz2HUM-n4kfs+kWWKw@mail.gmail.com>
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

Hi Erich,

PCB Elegance uses Viewplot 2.0, which did load the RS-274D Gerber 
correctly, but I need to pay 600 Euros for a Licence key to save the 
Gerber files in RS-274X format.

I will try your utilities, I was hoping Gerbv could lod in the older 
Gerber file format.

Regards,

Derek

On 19/05/2019 18:30, Erich Heinzle (a1039181 AT gmail DOT com) [via 
geda-user AT delorie DOT com] wrote:
> The now open source tool "pcb elegance" gerber load code appears to cope 
> with gerber aperture files. You may be able to load up the old gerbers 
> and aperture files and then attempt export of rs-274x gerbers from pcb 
> elegance.
> 
> Once you have rs-274x gerbers, they xan be turned intoa footprint with 
> translate2geda or translate2coralEDA for loading into gEDA pcb or into 
> pcb-rnd.
> 
> I managed to get pcb elegance running under wine on lubuntu. Their 
> gerber viewing tool seems to cope better with loading polygonal flashed 
> apertures than the pcb tool, but this should not be an issue for a 1990s 
> rs-274d board iiuc.
> 
> Failing that, i could try to add the ability to load an aperture file in 
> conjunction with a gerber file in my utilities translate2geda and 
> translate2coralEDA (available on github).
> 
> translate2coralEDA exports proper padstacks for pcb-rnd with polygonal 
> pad definitions, allowing round rect, obround, square, rect, circular, 
> etc pads, which may not be an issue for a 1990s board, but, you may be 
> able to take advantage of the padstack prototypes in pcb-rnd to add 
> drills to all padstacks of the same geometry, for example, in one fell 
> swoop, since a gerber layer will not include drill information.
> 
> Good luck!
> 
> Erich
> 
> 
> 
> 
> On Sun, 19 May 2019 18:18 Derek Stewart (derek AT q40 DOT de 
> <mailto:derek AT q40 DOT de>) [via geda-user AT delorie DOT com 
> <mailto:geda-user AT delorie DOT com>], <geda-user AT delorie DOT com 
> <mailto:geda-user AT delorie DOT com>> wrote:
> 
>     Hi,
> 
>     I have an old computer project designed in the late 1990s, for a 68060
>     single board computer, I used to produce, from Gerber files in RS-274D.
>     But not many PCB manufacturers use the RS-274D format.
> 
>     The Gerber files were produced in PCAD for DOS, which I have never
>     found
>     an implementation of PCAD, Protel, Tango PCB or Altium Designer to read
>     the binary PCB files.
> 
>     I would like to make some more PCBs, but I only have the RS-274D Gerber
>     files, what is hte best way to convert them to RS-274X or more modern
>     standard.
> 
>     -- 
>     Regards,
> 
>     Derek
> 

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019