delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2018/02/17/15:41:56

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
Subject: Re: [geda-user] (Off-topic) Question wrt driving HV piezo transducer
To: geda-user AT delorie DOT com
References: <c3aa1897-3806-3f72-feef-85551a63c2db AT linetec DOT nl>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802091324350 DOT 12270 AT igor2priv>
<f2259553-7015-8fc8-33b2-8ca8be6c5a45 AT linetec DOT nl>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802091427450 DOT 12270 AT igor2priv>
<20180209161532 DOT 6AF57804CEFA AT turkos DOT aspodata DOT se>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802091735590 DOT 12270 AT igor2priv>
<20180209204934 DOT CAA35804CEFA AT turkos DOT aspodata DOT se>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802100406500 DOT 12270 AT igor2priv>
<b125c1d5-48a1-c1dc-3ee1-db9875d50bf6 AT linetec DOT nl>
<c49d734f1b1f6373733e6f9935afff35 AT iae DOT nl>
<da435a2d-0bd0-f6d7-7d9a-05394665621c AT linetec DOT nl>
<aeedf5b6a230f39abdc82845a57a8b1b AT iae DOT nl>
<1a5665d2-c032-29f3-6de3-d4e3cd52f42b AT linetec DOT nl>
<8a6378847926baf01ef4fca1383d2bb9 AT iae DOT nl>
<d97f467d-6623-bee0-d63e-1d9daba345d0 AT linetec DOT nl>
<cfd1ba65-665b-98cf-86e6-92500a4f560e AT ecosensory DOT com>
<23accb16-b75d-b195-772d-2fe3c80a420e AT linetec DOT nl>
<4346c80d-d241-d768-ae8d-5ee39242719a AT ecosensory DOT com>
<519f49d1-11c6-2001-41e8-d1db0cfa9fcd AT linetec DOT nl>
<94acaa2d-2667-d977-6e67-64191583904e AT ecosensory DOT com>
From: "Richard Rasker (rasker AT linetec DOT nl) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Message-ID: <603182b2-9402-dfae-0104-9e6634330411@linetec.nl>
Date: Sat, 17 Feb 2018 21:40:17 +0100
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:52.0) Gecko/20100101
Thunderbird/52.6.0
MIME-Version: 1.0
In-Reply-To: <94acaa2d-2667-d977-6e67-64191583904e@ecosensory.com>
X-MIME-Autoconverted: from quoted-printable to 8bit by delorie.com id w1HKeLSC026459
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

Hello John,

Op 17-02-18 om 18:29 schreef John Griessen (john AT ecosensory DOT com) [via 
geda-user AT delorie DOT com]:
> On 02/17/2018 05:28 AM, Richard Rasker (rasker AT linetec DOT nl) [via 
> geda-user AT delorie DOT com] wrote:
>>
>> Ah, I understand now. As mentioned, I only need 41 kHz, as that is 
>> the f0 of the transducer.
>
> You may not be able to drive all that power at 2500V, certainly not 
> easy with a doubler sagging down,
> Do you really need to measure that fast?  If not, then the switching 
> speed can be 80 or 60 or 50 kHz, and
> maybe 6 of those needed to ramp up to near 2500V then settle 
> accurately on a valued for measuring position
> such as 2330V.  So overall response time would be about:  72 
> microseconds.  (13.8kHz rep rate.)

Hm, I'm not sure if we still have a serious misunderstanding here... 
Here's the complete specification:

Transducer:
f0: 41 kHz
C0: 5nF +/-20%
Vpp-max: 1800V

Intended drive signal: 1 - 1.5 ms bursts (so 40-60 periods) @ 1500Vpp, 5 
Hz repetition rate.

> I also found this calculator: 
> http://www.dicks-website.eu/coilcalculator/index.html
>
> Yep, that's what I used.

I selected a 3C90 Ferroxcube core (the ETD29/16/10-3C90) and filled in 
the following values:
Bmax = 0.2T (rather lower than the specified 330mT max, to be on the 
safe side)
Cross-section = 76 mm²
mu-e = 1770
Al = 2350 nH/n²
=======
12V RMS in
600V RMS out (=~ 1700Vpp)
f = 41000 Hz
-> 5 turns primary, 250 turns secondary
=======
Primary wire diameter: 0.5 mm
Secondary wire diameter: 0.05 mm
Length per turn primary: 35 mm
Length per turn secondary: 35 mm
Load resistor: 2K

This produces still workable values for primary input current (~14A) and 
losses at a decent output voltage.

[offer for sending me some rejects]
Well, thank you, that is very kind! But I think I'll go with the 
selected 3C90 core set and try to build my own transformer.
Not only will it no doubt be a valuable experience, I can tune it to the 
exact desired specifications, whereas your devices probably have a too 
high output voltage, and I doubt if I can disassemble them to take off 
some of the secondary.

I will need to be careful about secondary insulation of course, but from 
what I see, the bobbin offers room for a few (improvised) chambers.

One thing is certain: HV transformers are almost an art and a science in 
and of themselves...

But thanks again,

Best regards,

Richard

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019