delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2018/02/17/06:30:31

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
Subject: Re: [geda-user] (Off-topic) Question wrt driving HV piezo transducer
To: geda-user AT delorie DOT com
References: <c3aa1897-3806-3f72-feef-85551a63c2db AT linetec DOT nl>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802091235090 DOT 12270 AT igor2priv>
<6221de93-bb98-d397-79b4-eecf3975c2e6 AT linetec DOT nl>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802091324350 DOT 12270 AT igor2priv>
<f2259553-7015-8fc8-33b2-8ca8be6c5a45 AT linetec DOT nl>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802091427450 DOT 12270 AT igor2priv>
<20180209161532 DOT 6AF57804CEFA AT turkos DOT aspodata DOT se>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802091735590 DOT 12270 AT igor2priv>
<20180209204934 DOT CAA35804CEFA AT turkos DOT aspodata DOT se>
<alpine DOT DEB DOT 2 DOT 00 DOT 1802100406500 DOT 12270 AT igor2priv>
<b125c1d5-48a1-c1dc-3ee1-db9875d50bf6 AT linetec DOT nl>
<c49d734f1b1f6373733e6f9935afff35 AT iae DOT nl>
<da435a2d-0bd0-f6d7-7d9a-05394665621c AT linetec DOT nl>
<aeedf5b6a230f39abdc82845a57a8b1b AT iae DOT nl>
<1a5665d2-c032-29f3-6de3-d4e3cd52f42b AT linetec DOT nl>
<8a6378847926baf01ef4fca1383d2bb9 AT iae DOT nl>
<d97f467d-6623-bee0-d63e-1d9daba345d0 AT linetec DOT nl>
<cfd1ba65-665b-98cf-86e6-92500a4f560e AT ecosensory DOT com>
<23accb16-b75d-b195-772d-2fe3c80a420e AT linetec DOT nl>
<4346c80d-d241-d768-ae8d-5ee39242719a AT ecosensory DOT com>
From: "Richard Rasker (rasker AT linetec DOT nl) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
Message-ID: <519f49d1-11c6-2001-41e8-d1db0cfa9fcd@linetec.nl>
Date: Sat, 17 Feb 2018 12:28:40 +0100
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:52.0) Gecko/20100101
Thunderbird/52.6.0
MIME-Version: 1.0
In-Reply-To: <4346c80d-d241-d768-ae8d-5ee39242719a@ecosensory.com>
X-MIME-Autoconverted: from quoted-printable to 8bit by delorie.com id w1HBSjcL012384
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

Hello John,

Op 16-02-18 om 22:46 schreef John Griessen (john AT ecosensory DOT com) [via 
geda-user AT delorie DOT com]:
> On 02/16/2018 11:22 AM, Richard Rasker (rasker AT linetec DOT nl) [via 
> geda-user AT delorie DOT com] wrote:
>> this exact same half H-design is used in 100 kHz PWM motor drives and 
>> performs just fine).
>
> My question is not about the speed of switching, but of the overall 
> response time.
>
> My center tapped push pull can handle 6 microsecond plus and 6 us 
> minus pulses.  80kHz rep rate.
>
> It's all easier, (not saturating), if you can do with slower, thus my 
> question.
>
> 100kHz is the fastest most ordinary switcher cores run at, so there is 
> easy shopping from 40kHz to 100kHz,
> and you would not want to be below 40kHz so it is less audible.

Ah, I understand now. As mentioned, I only need 41 kHz, as that is the 
f0 of the transducer.

Also, I'm still undecided on the type of transformer and thus the 
circuitry; a transformer with a single primary coil for 12->1200 volts 
probably ends up being a custom-made part.
I'd expect that suitable CCFL transformers should be available 
off-the-shelf, but then again, a cursory search reveals that almost all 
commercially available types are EOL, and definitely not recommended for 
new designs. Not surprising really, given that LEDs have all but 
replaced CCFL tubes.
So perhaps rolling my own is better after all.

Anyway, thanks again for new and useful tidbits of information. As I 
said: I'm learning a lot here!

Best regards,

Richard

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019