delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2016/10/17/12:48:15

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
Message-ID: <1476722709.2914.98.camel@linetec>
Subject: Re: [geda-user] [off-topic] Looking for PCB edge connector pins for
perpendicular solder connection
From: "Richard Rasker (rasker AT linetec DOT nl) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
To: geda-user AT delorie DOT com
Date: Mon, 17 Oct 2016 18:45:09 +0200
In-Reply-To: <7a275aa777451816d490b375961e3ff6@tfsoft.org.ua>
References: <20161012013026 DOT 25221 DOT qmail AT rahul DOT net>
<20161012023951 DOT 43F528126612 AT turkos DOT aspodata DOT se>
<526c176c-62b4-9219-3919-83df144acc37 AT ecosensory DOT com>
<20161015040106 DOT 48C8B812661A AT turkos DOT aspodata DOT se>
<20161015082035 DOT 25529 DOT qmail AT rahul DOT net>
<20161015193628 DOT EA9FE812661A AT turkos DOT aspodata DOT se>
<1476644904 DOT 2890 DOT 33 DOT camel AT linetec>
<7a275aa777451816d490b375961e3ff6 AT tfsoft DOT org DOT ua>
Organization: Linetec
X-Mailer: Evolution 3.10.4-0ubuntu2
Mime-Version: 1.0
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

Anton Dubniak schreef op ma 17-10-2016 om 00:54 [+0300]:
> > I need to connect one PCB perpendicular to another, within a really
> > tight space. Now I recall having seen small PCB edge connector pins, 
> > the
> > shape a bit reminiscent of a tuning fork or Y, with two short tines
> > connected to the edge of one PCB and a single through-hole pin fitting
> > in a solder connection in the other PCB.
> 
> Not sure if this will fit your needs, but anyway...
> 
> Attached are my symbol and footprints (mechanically vetted) for M.2/NGFF 
> connector, which is super-compact (22mm wide, 67 contact positions 
> (minus those used as a key)), but there is no connector with 
> perpendicular orientation described by this standard, only parallel ones 
> (see image on the Mouser page).

Hi Anton,

Thank you for your trouble, but these are still way too large. I'm
looking for very small separate solder pins, like the ones used to make
these hybrid circuits:
https://i.ytimg.com/vi/3IYWeH_4QCE/maxresdefault.jpg


Best regards,

Richard Rasker

Linetec
-- 
Linetec Translation and Technology Services
Vleerkottelanden 14
7542 MJ  Enschede
The Netherlands

+31-53-4350834

http://www.linetec.nl/
e-mail: rasker AT linetec DOT nl


- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019