X-Authentication-Warning:	delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient:	geda-user AT delorie DOT com
X-Mailer:	exmh version 2.8.0 04/21/2012 (debian 1:2.8.0~rc1-2) with nmh-1.5
X-Exmh-Isig-CompType:	repl
X-Exmh-Isig-Folder:	inbox
From:	karl AT aspodata DOT se
To:	geda-user AT delorie DOT com
Subject:	Re: [geda-user] symbol generators
In-reply-to:	<20150709094946.GB15170@localhost.localdomain>
References:	<20150701200650 DOT 4C0928038A29 AT turkos DOT aspodata DOT se> <20150703075321 DOT GB15019 AT localhost DOT localdomain> <CAHUm0tO3+DzO1A5DSzuBO1jf_Sa3e-c3r3xjYoZ0BtsgGt4M_w AT mail DOT gmail DOT com> <20150705021003 DOT 1E8958038A2C AT turkos DOT aspodata DOT se> <20150709094946 DOT GB15170 AT localhost DOT localdomain>
Comments:	In-reply-to "Vladimir Zhbanov (vzhbanov AT gmail DOT com) [via geda-user AT delorie DOT com]" <geda-user AT delorie DOT com>
	message dated "Thu, 09 Jul 2015 12:49:46 +0300."
Mime-Version:	1.0
Message-Id:	<20150711221848.3CBFA8038A32@turkos.aspodata.se>
Date:	Sun, 12 Jul 2015 00:18:48 +0200 (CEST)
X-Virus-Scanned:	ClamAV using ClamSMTP
Reply-To:	geda-user AT delorie DOT com
Errors-To:	nobody AT delorie DOT com
X-Mailing-List:	geda-user AT delorie DOT com
X-Unsubscribes-To:	listserv AT delorie DOT com

Vladimir:
> On Sun, Jul 05, 2015 at 04:10:02AM +0200, karl AT aspodata DOT se wrote:
> > Erich:
> > > Because it was only a little bit of extra work, I have created a Hybrid
> > > Ring Coupler footprint generator based on the Wilkinson Power Divider
> > > Footprint generator.
> > ...
> > 
> > The page to change is:
> > 
> >  http://wiki.geda-project.org/geda:pcb_footprints
> > 
> > perphaps you can collect info about various footprint generators and 
> > suggest what to write on that page.
> 
> Added, thanks,

Very nice Vladimir,

I have one that could possible be included:

 http://turkos.aspodata.se/git/openhw/share/pcb/gen.pl

to

 http://wiki.geda-project.org/pcb:footprint_generators

to use it you have to read and modify the code to your liking...

///

In http://wiki.geda-project.org/geda:pcb_footprints under
"Footprint basics" / "For writing footprints in text, refer to:"
the link "Footprints wiki page" refers to the same page as you are 
viewing.
 Perhaps one should just remove the line.

///

(same page)

"PCB Footprint FAQ" / "How do I make a 2-sided pad?"

 You do it by makeing two pads at the same position and same pin number,
 but the second one with the flag "onsolder". Like in:

   Pad[ 10mm -3mm  10mm 3mm  2.0mm 0.5mm 0.2mm "1" "1" "square" ]
   Pad[ 10mm -3mm  10mm 3mm  2.0mm 0.5mm 0.2mm "1" "1" "square,onsolder" ]

"Edge Connectors"

 Do a 2-sided pad as above. If you want the shape of the connector pad 
 to be square at the edge end and halfround at the pcb-iteriour end, use 
 two owerlapping pads per side, Like in:

   Pad[  0   -3mm   0   3mm  2.0mm 0.5mm 0.2mm "1" "1" "square" ]
   Pad[  0   -3mm   0   5mm  2.0mm 0.5mm 0.2mm "1" "1" "" ]

   Pad[  0   -3mm   0   3mm  2.0mm 0.5mm 0.2mm "1" "1" "square,onsolder" ]
   Pad[  0   -3mm   0   5mm  2.0mm 0.5mm 0.2mm "1" "1" "onsolder" ]

///

http://wiki.geda-project.org/geda:pcb_tips, section 
"Footprint issues" should be moved to
http://wiki.geda-project.org/geda:pcb_footprints, or what do you think ?

Regards,
/Karl Hammar

-----------------------------------------------------------------------
Aspö Data
Lilla Aspö 148
S-742 94 Östhammar
Sweden
+46 173 140 57

- Raw text -