delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2014/02/27/15:28:40

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
d=gmail.com; s=20120113;
h=mime-version:in-reply-to:references:date:message-id:subject:from:to
:content-type;
bh=D182JTcKFbuIyVExYAU7Ljjg+k6sHuBmdk038vgyJuM=;
b=w4Lh/LqGtYsqMReupy3+KHmb9+D+vBF9yEXv5QodGat+bQ8J6dFqxuHrNgCH+wOc0o
OHEiLKbK7xDmkTWR2AYJuJMnBviijrRTbC73p0tR2wwwJAaNspVbnf1y3gO0fGqe0Eg/
wXiw7i2Dk0/qtSgPuezwsYLH90borkCS0c9BNs1iRDtLGCb0u64d/tFArZV0msJos9OK
V2tz5axIenqyTc5DE8mL1h5qFwdexP/QLLRPo9j1j7jDP6LgnTavclD5b7eujIUJmhHY
TSZ964dk7d09nbgjDcsnB7T7XLdclqmeHybyf5CTvwbKPyNQfUXjy+hycwlki308TR2x
9Lrg==
MIME-Version: 1.0
X-Received: by 10.58.200.168 with SMTP id jt8mr2970386vec.30.1393532899818;
Thu, 27 Feb 2014 12:28:19 -0800 (PST)
In-Reply-To: <CALSZ9gohqcqTT7y8x8x2wZdrcv8s2M-DhaN8vB5Zf6uvpRrCYA@mail.gmail.com>
References: <CALSZ9gohqcqTT7y8x8x2wZdrcv8s2M-DhaN8vB5Zf6uvpRrCYA AT mail DOT gmail DOT com>
Date: Thu, 27 Feb 2014 15:28:19 -0500
Message-ID: <CAOFvGD7EeNMkku3+C-=CZK6etu_Q_y6aF-whxFLzivcu6qj5ag@mail.gmail.com>
Subject: Re: [geda-user] Via under a pad?
From: Jason White <whitewaterssoftwareinfo AT gmail DOT com>
To: geda-user AT delorie DOT com
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

I am no expert, so take this with a grain of salt.

In many cases its fine, with BGA's and other fine pitch devices there
is not much of a choice. I have seen it done on many, many high
density boards. I can imagine potential issues with dry joints if
excessive amounts of solder flow down through the via. However, that
only really should become a factor when a) the volume of the via
becomes a significant portion compared to applied solder paste or b)
area of exposed TH plating of the via becomes significant in
comparison to the pad. As you hint at the via of will exhibit a
tendency to become filled with solder but for small "mico-vias" it
really shouldn't matter much at all.

On Thu, Feb 27, 2014 at 3:01 PM, Rob Butts <r DOT butts2 AT gmail DOT com> wrote:
> Is it bad practice to put vias under pads?  These pads are twice as big as
> the vias.
>
> Just curious.



-- 
Jason White

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019