delorie.com/archives/browse.cgi   search  
Mail Archives: geda-user/2012/05/23/16:59:44

X-Authentication-Warning: delorie.com: mail set sender to geda-user-bounces using -f
X-Recipient: geda-user AT delorie DOT com
DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed;
d=gmail.com; s=20120113;
h=mime-version:in-reply-to:references:date:message-id:subject:from:to
:content-type;
bh=8t3x35PtGX38/AgWnz6AXD4O3cMBt0ROcc/xE9+uHx4=;
b=xGhDkxYjgI/3caiSuD0T4YRGy39QFCKnbpwqqHAj+JFfZQXT3+gIYep2ZDQ6bLZEJs
CbYfEtBTVnlOgeBuj8agskY9PNsDEHM4C9t/XZ62b7ZiChUbuBAlaJbPAZOomvcgiBkh
W2H0Dz76HEP05GRB7BrMt5Yy98YDhucqvCwBgbNuaeBhiey7XceSBhPo6IeH3WN+wdpc
4wDwoDgI5PVxh1x+v8aeDR4p6ep6jLZb+o9HkgPqDi+Tcg5jpNUkCGrb6XYqPL/hcjBL
T1uwSLoug8yDjF1g0NSCwr6r8L+F0bHKgOuWzqQnLpX23HTUwmdRJhnJaHSjncFpibZx
iLuQ==
MIME-Version: 1.0
In-Reply-To: <201205232050.q4NKoM3Q000589@envy.delorie.com>
References: <CALSZ9gqde8vwZ+xUzZXv_nmrzoyr1kHJSsgPO0-VUeXoY7MKiw AT mail DOT gmail DOT com>
<201205232050 DOT q4NKoM3Q000589 AT envy DOT delorie DOT com>
Date: Wed, 23 May 2012 16:59:32 -0400
Message-ID: <CALSZ9gqcz22gO=PVAEWMDzDygB6HLb6gtGuOoBQaJT+3S8iHtg@mail.gmail.com>
Subject: Re: [geda-user] PCB Pad discrepancy
From: Rob Butts <r DOT butts2 AT gmail DOT com>
To: geda-user AT delorie DOT com
Reply-To: geda-user AT delorie DOT com
Errors-To: nobody AT delorie DOT com
X-Mailing-List: geda-user AT delorie DOT com
X-Unsubscribes-To: listserv AT delorie DOT com

--00151761c7de7937e304c0ba696c
Content-Type: text/plain; charset=ISO-8859-1

I was going by the footprint creation guide and the fact that your PCB
showed the correct dimensions verifies the statement.  Now I just have to
figure out why my PCB isn't getting it right.

Thanks for verifying it.

On Wed, May 23, 2012 at 4:50 PM, DJ Delorie <dj AT delorie DOT com> wrote:

>
> > I want to create a pad 1.25" x 0.24"
> >
> > My pad statement is:
> >
> > Pad[75000 25000 75000 126000 24000 2000 26000 "" "1" "square"]
> >
> > When I do a cntrl-R over the pad it gives me a width = 240 mils and
> length
> > = 641.38 mils
> >
> > I have gone over the math 5 times now.  Does anyone see what I'm doing
> > wrong?
>
> http://www.brorson.com/gEDA/land_patterns_20070805.pdf
>
> width = 240 mil
> legnth = (1260-250) + 240 mil = 1250 mil
>
> My pcb's (git head) report says:
>
> PAD ID# 7;  Flags:"square,edge2"
> FirstPoint(X,Y)  = (2125.00, 1225.00) mil; ID = 0.
> SecondPoint(X,Y) = (2125.00, 2235.00) mil; ID = 0.
> Width = 240.00 mil.  Length = 1250.00 mil.
>  <<<<<<<<<<<<<<<<<<
> Clearance width in polygons = 10.00 mil.
> Solder mask = 260.00 mil x 1270.00 mil (gap = 10.00 mil).
> Name = "".
> It is owned by SMD element 0603N
>  as pin number 1 and is on the component
> side of the board.
>

--00151761c7de7937e304c0ba696c
Content-Type: text/html; charset=ISO-8859-1
Content-Transfer-Encoding: quoted-printable

I was going by the footprint creation guide and the fact that your PCB show=
ed the correct dimensions verifies the statement.=A0 Now I just have to fig=
ure out why my PCB isn&#39;t getting it right.<br><br>Thanks for verifying =
it.<br>
<br><div class=3D"gmail_quote">On Wed, May 23, 2012 at 4:50 PM, DJ Delorie =
<span dir=3D"ltr">&lt;<a href=3D"mailto:dj AT delorie DOT com" target=3D"_blank">d=
j AT delorie DOT com</a>&gt;</span> wrote:<br><blockquote class=3D"gmail_quote" st=
yle=3D"margin:0pt 0pt 0pt 0.8ex;border-left:1px solid rgb(204,204,204);padd=
ing-left:1ex">
<div class=3D"im"><br>
&gt; I want to create a pad 1.25&quot; x 0.24&quot;<br>
&gt;<br>
&gt; My pad statement is:<br>
&gt;<br>
&gt; Pad[75000 25000 75000 126000 24000 2000 26000 &quot;&quot; &quot;1&quo=
t; &quot;square&quot;]<br>
&gt;<br>
&gt; When I do a cntrl-R over the pad it gives me a width =3D 240 mils and =
length<br>
&gt; =3D 641.38 mils<br>
&gt;<br>
&gt; I have gone over the math 5 times now. =A0Does anyone see what I&#39;m=
 doing<br>
&gt; wrong?<br>
<br>
</div><a href=3D"http://www.brorson.com/gEDA/land_patterns_20070805.pdf" ta=
rget=3D"_blank">http://www.brorson.com/gEDA/land_patterns_20070805.pdf</a><=
br>
<br>
width =3D 240 mil<br>
legnth =3D (1260-250) + 240 mil =3D 1250 mil<br>
<br>
My pcb&#39;s (git head) report says:<br>
<br>
PAD ID# 7; =A0Flags:&quot;square,edge2&quot;<br>
FirstPoint(X,Y) =A0=3D (2125.00, 1225.00) mil; ID =3D 0.<br>
SecondPoint(X,Y) =3D (2125.00, 2235.00) mil; ID =3D 0.<br>
Width =3D 240.00 mil. =A0Length =3D 1250.00 mil. =A0 =A0 =A0 =A0 =A0 =A0 =
=A0 =A0&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;&lt;=
&lt;<br>
Clearance width in polygons =3D 10.00 mil.<br>
Solder mask =3D 260.00 mil x 1270.00 mil (gap =3D 10.00 mil).<br>
Name =3D &quot;&quot;.<br>
It is owned by SMD element 0603N<br>
 =A0as pin number 1 and is on the component<br>
side of the board.<br>
</blockquote></div><br>

--00151761c7de7937e304c0ba696c--

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019