delorie.com/archives/browse.cgi   search  
Mail Archives: geda-help/2014/04/07/10:00:33

X-Authentication-Warning: delorie.com: mail set sender to geda-help-bounces using -f
X-Recipient: geda-help AT delorie DOT com
Message-ID: <5342AF6B.6010405@mochima.com>
Date: Mon, 07 Apr 2014 10:00:11 -0400
From: Carlos Moreno <moreno+geda-help AT mochima DOT com>
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:24.0) Gecko/20100101 Thunderbird/24.4.0
MIME-Version: 1.0
To: geda-help AT delorie DOT com
Subject: Re: [geda-help] Workflow Schematic Editor -> schem2pcb -> PCB Designer
won't work!
References: <533F4740 DOT 5010606 AT mochima DOT com> <alpine DOT DEB DOT 2 DOT 00 DOT 1404050517330 DOT 8305 AT igor2priv> <533F89FE DOT 2060808 AT mochima DOT com> <alpine DOT DEB DOT 2 DOT 00 DOT 1404050746030 DOT 8305 AT igor2priv> <534000E2 DOT 5080703 AT mochima DOT com> <alpine DOT DEB DOT 2 DOT 00 DOT 1404060625040 DOT 8305 AT igor2priv>
In-Reply-To: <alpine.DEB.2.00.1404060625040.8305@igor2priv>
X-Added-Header:
Reply-To: geda-help AT delorie DOT com

Hi Tibor,

On 14-04-06 12:38 AM, gedah AT igor2 DOT repo DOT hu wrote:
> Judging from this one, it seems like the problem is specific to U1 - 
> the connection between the resistors worked well. However, I can't 
> check again because you have changed a few things since (resistor 
> footprints, the symbol behind LME, as you mentioned).

Well, the uploaded LME symbol was after changing the pintype=nc to 
pintype=pas,
so the only change, really, was the footprint for the resistors. And the 
outcome
when using my own R-SMT-0805.fp was exactly the same  (of course, with 
the SMT
footprints showing instead of the through-hole ones for R025).

>
> 1. hover the mouse over the middle of U1, between pins, and press 'd'; 
> this would annotate each pin with its pin number. Even better please 
> do this for the resistors as well. Please make a screenshot with these 
> annotations.

Did that.  It shows 1 through 15 at the correct positions.  Same for the 
resistors
(shows 1 and 2 for the two SMT pads)

> 2. upload the pcb tight after gsch2pcb, then open from pcb, load 
> netlist, disperse, optimize rats, make sure the same resistor-only-net 
> has the rats then save the pcb and upload that as well.

I'm not sure what you're referring to in here --- what is "pcb tight"??

Also, notice that I've been using the GUI version of gsch2pcb  (I go to
Nautilus File browser, then right-click on nada-LME49811.sch and
select  "Open with gEDA Schematic -> PCB Project", like they show
in the youtube video --- http://www.youtube.com/watch?v=2Faf2nACG34,
around minute 3:30 of the video).

Do notice that I did not create any .prj file  (on the Blinker board 
section
in the tutorial in http://www.delorie.com/pcb/docs/gs/gs.html, they do it
that way, but I could never figure out all the details, so I went with the
workflow they show in the youtube videos).

>
> 3. please upload the .net file gsch2pcb spits out
>
> 4. please post the error log for this session (again there's been a 
> lot changed, footpritns, symbols...)
>
> The netlist is embedded in the .pcb, so if PCB does something bad to 
> the netlist internally, comparing the files produced in step 2. and 3. 
> would help. If PCB has problems with the pin numbering, the screenshot 
> of 1. woudl show. Currently these are the things I think could go 
> wrong there.

I'll keep this in mind.  I was quite busy over the weekend and will be 
today
and tomorrow, but as soon as I have some time available, I will do these
and upload files and screenshots or screen video  (this recordmydesktop
package works really well!!!!  :-) )

Thanks!
Carlos
--

- Raw text -


  webmaster     delorie software   privacy  
  Copyright © 2019   by DJ Delorie     Updated Jul 2019